Hitachi DV-RX5000U manual Antenna and television connections, Setting up

STEP 1 Antenna and television connections

Preparation	To enjoy sound through other audio equipment (➜page 42)
≥Refer to the television’s operating instructions.	To enjoy progressive video
≥Turn the television off and disconnect its AC power supply cord.	Connect to the component video (480P) input terminals on a televi-
	sion compatible with this unit’s copy guard system. (Video will not
	be displayed correctly if connected to an incompatible television.)

Television
		AUDIO	VIDEO
		IN	IN	VHF/UHF
		R L		RF IN
AC power supply cord (included)		Red White Yellow
Connect last.
Also connect the AC
power supply cords for	Audio/Video cable
the other equipment.			75 ≠ coaxial cable
	(included)		(included) ➜below

To household AC outlet

(AC 120 V, 60 Hz)

Red White Yellow

Cooling fan

	To the antenna
	Cable TV
Outdoor antenna
	Indoor antenna
	or
If the connector	Antenna cable
doesn’t match	(usually discon-
➜page 44
	nected from the
	television).

This unit

Setting up

										RF IN
R-AUDIO-L	VIDEO	S-VIDEO	(L1)				Y	PB	PR
IN 1
								OPTICAL
				OUT						RF OUT
IN 3							COMPONENT	DIGITAL AUDIO OUT		VHF/UHF
R-AUDIO-L	VIDEO	S-VIDEO	(L3)	R-AUDIO-L	VIDEO	S-VIDEO	VIDEO OUT
							(480P/480I)	(PCM/BITSTREAM)

S-VIDEO OUT terminal

The S-VIDEO OUT terminal achieves a more vivid picture than the VIDEO OUT terminal by separating the chrominance (C) and luminance (Y) signals. (Actual results depend on the tele-

vision.)Television

	S video cable	S VIDEO
		IN
OUT	(not included)
R-AUDIO-L VIDEO	S-VIDEO

When making this connection, ensure you connect the audio cables to the corresponding audio input terminals on the televi- sion.

75 ≠ coaxial cable

≥The signal from the antenna passes through this unit and along

the 75 ≠ coaxial cable to the television even when this unit is

turned off. You don’t have to connect the antenna to the televi-

sion.

≥The picture and sound signal from this unit does not go through

the 75 ≠ coaxial cable to the television. Make sure you connect

one of the following terminals on this unit to the television: the

Television

COMPONENT

VIDEO IN

Y PB PR

Video cable

(not included)

Y PBPR

	OPTICAL
COMPONENT	DIGITAL AUDIO OUT
VIDEO OUT
(480P/480I)	(PCM/BITSTREAM)

COMPONENT VIDEO OUT terminal

These terminals can be used for either interlace or progressive output and provide a purer picture than the S-VIDEO OUT terminal.

Connection using these terminals outputs the color difference signals (PB/PR) and luminance signal (Y) separately in order to achieve high fidelity in reproducing colors.

≥The description of the component video input terminals depends on the televi- sion or monitor (e.g. Y/PB/PR, Y/B-Y/R-Y, Y/CB/CR). Connect to terminals of the same color.

≥After making this connection, change the black level for a better picture (➜page 47, Video–Black Level Control).

When making this connection, ensure you connect the audio cables to the corresponding audio input terminals on the television.

AUDIO/VIDEO terminal, the S-VIDEO OUT terminal or the

COMPONENT VIDEO OUT terminal. If the television has none

of these terminals, consult your local dealer.

Conserving power

This unit consumes a small amount of power, even when it is turned off (approx. 3.2 W). To save power when the unit is not to be used for a long time, unplug it from the household AC outlet.

Do not connect the unit through a video cassette recorder

Video signals fed through video cassette recorders will be affected by copyright protection systems and the picture will not be shown correctly on the television.

5