Manuals / Hitachi / Computer Equipment / Computer Drive

Hitachi HUS157336EL3800, HUS157373EL3800 1 Connector Layout WIDE LVD drive, 2 Connector view

Models: HUS157373EL3800 HUS157373EL3600 HUS157336EL3600 HUS157336EL3800

1 46

Download 46 pages 50.66 Kb

Page 31

Image 31

Figure 10.1 Connector Layout (WIDE LVD drive)

10.3Connector Layout WIDE LVD drive

SCSI Bus Connector C1

Auxiliary Connector C4

Power Connector C2

Figure 10.1 Connector Layout (WIDE LVD drive)

C2-1 : 12V

C2-2 : GND (12V Return)

C2-3 : GND (5V Return)

C2-4 : 5V

C1	1	C4	1		C2
34	1	11	1
68	35	12	2	4	3	2	1

Figure 10.2 Connector view

Note: The SCSI ID setting is to be set via the C3 connector (not by C4) normally.

In case the SCSI ID setting is done by remote switch via the C4 connector and remote cable, remove all Jumper Sockets from the C3 connector to avoid SCSI ID control conflicts.

Drawing No. Sheet No. Revision 5
K6602906	31/46	2003/6/12

Page 31

Image 31

Hitachi HUS157336EL3800, HUS157373EL3800, HUS157336EL3600 specifications 1 Connector Layout WIDE LVD drive, 2 Connector view

Contents

Hitachi Global Storage Technologies Hard Disk Drive Specifications Ultrastar 15K73-73/36 SCSI2003/6/12 Drawing No. Sheet No. RevisionK6602906 2/46Influence for environment General cautions for safetyHeadline of safety caution To use this product safelyTo use this product safely Continued Safety cautions for this productTo use this product safely Continued Warranty and Limited LiabilityPrecautions for handling DC power InterfaceConnecting Methods Summary of SCSI CommandsJumper connector layout SCSI Bus Connector C1Other connectors Jumper Socket settingTable 1.1 Models 1 Features2 Standards and Related Documents MEEPRML Table 3.1 Characteristics3 Description PowerK6602906 Table 3.2 Environmental conditions and reliability3.2 Environmental conditions and reliability Drawing No. Sheet No. RevisionFigure 3.1 Vibration test direction Figure 3.2 Shock test direction Power measurement Operating Table 4.1 DC Power Requirement 4 DC power InterfaceTable 4.2 Start and Stop time Fig 4.1 Current transition for +12V+12V Current A Drawing No. Sheet No. Revision 1. If Disable Auto Start mode is set C39-10 installedManually power on drives at intervals of more than 10 seconds 4.3.2 Spindle Start Selectionpower supply cable 5 Connecting MethodsFigure 5.1 Cabling layout WIDE LVD drive Terminator SCSI bus DC power GND19/46 5.2 Low voltage differential LVD modeDrawing No. Sheet No. Revision K66029066 SCSI Interface 11 Write Cache 8 Tagged Command Queuing9 S.M.A.R.T. Self - Monitoring, Analysis and Reporting Technology 10 Automatic Read ReallocationTable 6.1 SCSI Commands Supported 7 Mounting and Handling Table 6.1 SCSI Commands Supported ContinuedFig. 7.1 Orientations Figure 7.2 Example for mounting HDA upper surface spacer PCB parts sideFigure 7.3 Layout of Mounting holes Figure 7.4 Temperature Measurement Points Table 7.1 Temperature Limits unit CHDAbottom 8 Precautions for handling 9 Maintenance 10 Physical interface Table 10.1 Interface connectorsTable 10.3 Interface cable WIDE, LVD mode Table 10.2 Interface cable WIDE, Single-ended modeFigure 10.2 Connector view Figure 10.1 Connector Layout WIDE LVD driveC2-1 C2-2 GND 12V Return C2-3 GND 5V Return C2-4 Figure 10.4 Connector view Figure 10.3 Connector Layout SCA-2 LVD drive26.1 max DIFFSENS Table 11.1 Pin assignment of SCSI Bus Connector C111 Pin assignment WIDE, Single-ended modeTable 11.2 Pin assignment of SCSI Bus Connector C1 WIDE, LVD mode SCA-2, Single-ended mode Table 11.3 Pin assignment of SCSI Bus Connector C1Table 11.4 Pin assignment of SCSI Bus Connector C1 SCA-2, LVD mode K6602906 Table 11.5 Pin assignment of Auxiliary Connector C4 WIDE LVD drive11.2 Other connectors Drawing No. Sheet No. Revision5V C3-22 Figure 11.1 LED Driver+5V 5V C4-11 150 ohm 5V C3-22 150 ohm LED C4-8 LED C3-21 +5V 150 ohmAuxiliary Connector C4 12 Jumper Socket settingFigure 12.1 Jumper connector layout WIDE LVD drive Option Jumper Connector C3Option Jumper Connector C3 Figure 12.2 Jumper connector layout SCA-2 LVD driveDefault 12.2 Jumper socket settingThe Jumper sockets should be set only when the power is off Option Jumper Connector C3Install the Jumper Socket Option Jumper Connector C3Default Install the Jumper SocketK6602906 12.2.3 Disable Auto Start WIDE LVDSCA-2 LVD Drawing No. Sheet No. Revision12.2.4 Force Single-Ended bus mode WIDE LVD, SCA-2 LVD 12.2.6 SCSI bus Terminator Power WIDE LVD Table 12.1 Jumper socket Table 12.2 Extension connector