Adjusting depth of cut Fig, Stopper block Fig | Hitachi KM 12SC

English

HOW TO USE THE ROUTER

1. Adjusting depth of cut (Fig. 4)

(1)Place the tool on a flat wood surface.

(2)Turn the stopper block so that section to which the cutting depth setting screw on stopper block is not attached comes to the bottom of the stopper pole. Loosen wing bolt, allowing the stopper pole to contact with stopper block.

(3)Press the lock lever down and lower the tool body until the bit just touches the flat surface. Release the lock lever to hold the tool body down.

(4)Tighten wing bolt. Align the depth indicator with the “0” graduation.

(5)Loosen wing bolt, and raise until indicator aligns with the graduation representing the desired cutting depth.

(6)Press the lock lever and press the tool body down until the stopper block to obtain the desired cutting

depth.

2. Stopper block (Fig. 5)

Stopper Pole

Graduation

Lock Lever

Depth

Indicator

Wing Bolt

Stopper Block

Fig. 4

	The two cut-depth setting screws attached to the	Cut Depth
	stopper block can be adjusted to simultaneously	Cut Depth
	set three different cutting depths. Use a wrench	Setting
	set three different cutting depths. Use a wrench	Screw
	to tighten the nuts so that the cut-depth setting
	screws do not come loose at this time.	Fig. 5
	3. Upper limiting nuts (Fig. 6)	Fig. 5
	By turning the upper limiting nuts, the upper limit	Limiting
	of the tool body can be adjusted, when the tip of	Limiting
	of the tool body can be adjusted, when the tip of	Nut (B)
	the bit is retracted more than required in relation	Nut (B)
	the bit is retracted more than required in relation
	to the base plate surface, turn the upper limiting	Limiting
	nuts to lower the upper limit.	Limiting
	nuts to lower the upper limit.	Nut (A)
		Nut (A)

CAUTION:

Fig. 6

⬤The upper limiting nut (A) and upper limiting nut (B) must always be “jammed” together to prevent movement (caused by vibration) which could prevent full bit retraction.

⬤The upper limiting nuts must always be set so that bit can be retracted into base of router, clear of work.

2

Image 59

Hitachi KM 12SC, KM 12VC instruction manual Adjusting depth of cut Fig, Stopper block Fig, Upper limiting nuts Fig

Contents

Advertencia Router Toupie FresadoraAvertissement Contents Meanings of Signal Words Important Safety Information General Safety Rules Safety Specific Safety Rules and Symbols English USE of Extension Cord Make Them Available to Other Users Owners of this Tool Name of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Removing bits Installing and Removing BitsInstalling bits Adjusting depth of cut Installing the Motor HousingHOW to USE the Router Installing the motor housing Guiding the router Adjusting the rotation speed Model M12VC onlyCentering the template guide adapter Cutting English Maintenance and Inspection Modifications Model KM12VC, KM12SC AccessoriesStandard Accessories Model M12VC, M12SC Optional Accessories …………… sold separately Signification DES Mots Dõavertissement Informations Importantes DE SƒCURITƒ Conserver CES Instructions SecuriteRegles Generale DE Securite Franais Regles DE Securite Specifiques ET Symboles Avertissement Calibre Minimum DES Cordons Utilisation Dõun Cordon DE Rallonge NOM DES Parties Description Fonctionnelle Avant Lõutilisation Retrait de la mèche Installation ET Retrait DE LA MecheInstallation de la mèche Réglage de la profondeur de coupe Installation DU Carter MoteurInstallation du carter moteur Utilisation DE LA Toupie Guidage de la toupie Réglage de la vitesse de rotation Modèle M12VC seulementCentrage de l’adaptateur de guide de gabarit Coupe Remarque Entretien ET Inspection No. élément No. code No. utilisé Remarques Modèle KM12VC, KM12SC AccessoiresAccessoires Standard Modèle M12VC, M12SC Accessoires SUR Option Ééééé vendus sŽparŽment Significado DE LAS Palabras DE SE„ALIZACIîN INFORMACIîN Importante Sobre Seguridad Guarde Estas Instrucciones SeguridadNormas Generales DE Seguridad Espa-ol Normas Y SêMBOLOS ESPECêFICOS DE Seguridad Advertencia UTILIZACIîN DE UN Cable Prolongador Águarde Estas InstruccionesOtros Usuarios Propietarios DE Esta Herramienta Nomenclatura DESCRIPCIîN Funcional Antes DE LA OPERACIîN Aplicaciones Extracción de brocas INSTALACIîN Y EXTRACCIîN DE LAS BrocasInstalación de las brocas Ajuste de la profundidad de corte INSTALACIîN DE LA Carcasa DEL MotorCîMO Usar LA Fresadora Cómo guiar la fresadora Ajuste de la velocidad de rotación Modelo M12VC solamenteCentrado del adaptador de guía de la plantilla Corte Nota Mantenimiento y reparación Inspección de los tornillosInspección de la escobillas Fig Reemplazo de las escobillas Modificaciones Modelo KM12VC, KM12SC AccesoriosAccesorios ESTçNDAR Modelo M12VC, M12SC Accesorios Opcionales Ééééé de venta por separado M12VC M12SC KM12VC, KM12SC KM12VC KM12SC Hitachi Koki Canada Co Plunge Base Socle d’inclinaison Base de penetración Removing the fixed base Fig Meanings of Signal Words Replacing the BaseInstalling plunge base Upper limiting nuts Fig Adjusting depth of cut FigStopper block Fig Cutting Retrait du socle fixe Fig Remplacement DU SocleInstallation du socle d’inclinaison Signification DES Mots D’AVERTISSEMENT Ecrous de limite supérieure Fig Réglage de la profondeur de coupe FigButée Fig Séparé Avance de la toupie Instalación de la base de penetración Significado DE LAS Palabras DE SeñalizaciónReemplazo DE LA Base Desmontaje de la base fija Fig Tuercas limitadora superior Fig Cómo Usar LA RanuradoraAjuste de la profundidad de corte Fig Bloque de tope Fig Precaución Page Hitachi Koki Canada Co