Stop engine and let cool | Hobart Welding Products OM-240 438E

. A complete Parts List is available at wwwHobartWelders.com

8-4. Changing Engine Oil, Oil Filter, and Fuel Filter

Full

! Stop engine and let cool.

1Oil Drain Valve

21/2 ID x 7 in Hose

3Oil Filter

	Change engine oil and filter accord-
	ing to engine owner’s manual.
	!	Close valve and valve cap
		before	adding	oil	and
		running engine.
	Fill crankcase with new oil to full
	mark on dipstick (see Section 5-4).
	4	Fuel Filter
	5	Fuel Line
	Replace line if cracked or worn.
	Install new filter. Wipe up any spilled
	fuel.
	Start engine, and check for fuel
	leaks.
4	!	Stop engine, tighten connec-
		tions as necessary, and wipe
		up fuel.

Tools Needed:

244 033-A / S-0842

OM-240 438 Page 36

Page 40

Image 40

Hobart Welding Products OM-240 438E Changing Engine Oil, Oil Filter, and Fuel Filter, Stop engine and let cool, Up fuel

Contents

Processes OM-240 438EDescription From Hobart to You Protect Your Investment Table of Contents 10-1 Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can burn Fumes and Gases can be hazardous Buildup of GAS can injure or killARC Rays can burn eyes and skin Welding can cause fire or explosion Engine Hazards Hydraulic Hazards Compressed Air HazardsHydraulic Equipment can injure or kill Hydraulic Fluid can injure or kill Compressed AIR can injure or kill Fire or Explosion hazardOverheating can damage motors Falling Equipment can injure California Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Implanted Medical Devices Signification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer Indique des instructions spécifiques LES Pièces Chaudes peuvent provoquer des brûlures LES Fumées ET LES GAZ peu- vent être dangereuxLE Soudage peut provoquer un incendie ou une explosion LE Bruit peut affecter l’ouïe ’EXPLOSION DE LA Batterie peut provoquer des blessures Les Pièces Mobiles peuvent causer des blessures LES Étincelles À L’ÉCHAPPEMENT peuvent provoquer un incendie LA Chaleur DU Moteur peut pro- voquer un incendie Lire LES Instructions Risque D’INCENDIE OU LA Chute DE L’ÉQUIPEMENT peut provoquer des blessuresLE Surchauffement peut endommager le moteur électrique LES Étincelles Projetées peuvent provoquer des blessures UNE Remorque QUI Bascule peut provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Informations relatives aux CEM Principales normes de sécuritéEn ce qui concerne les implants médicaux − Specifications Symbol DefinitionsWeld, Power, and Engine Specifications − Definitions Dimensions, Weights, And Operating Angles Weight 562 lb 254 kg Dimensions For Units With Optional Running Gear DimensionsDuty Cycle Duty Cycle For CC/DC Mode For CC/AC ModeVolt-Ampere Curves Generator Power Curve Fuel Consumption − Installation Installing Welding GeneratorSerial Number And Rating Label Location Movement Location / Airflow Clearance Grounding Generator To Truck Or Trailer Frame GND/PE Engine Prestart Checks Oil Installing Exhaust Pipe Connecting Or Replacing the BatteryConnect negative − battery cable last + − Stop engine Failure to properly connect Connecting To Weld Output TerminalsTools Needed 3/4 Selecting Weld Cable Sizes 150 ft 200 ft 250 ft350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m 100 150 200 250 Start Your Professional Welding Career Now Engine Control Switch − Operating the Welding GeneratorFront Panel Controls Fine Control Cold Weather Engine Operation InfrequentlyLoaded Frequently Loaded Stop engine Typical Stick Welding Connections And Control SettingsElectrode − Operating Auxiliary Equipment Standard ReceptaclesGfci Receptacle Option At least once a month, run engine at Simultaneous Weld And Power Wiring Optional 240 Volt PlugCurrent Available in Amperes 240 Receptacle − Maintenance Maintenance Label Routine Maintenance 100200 500 Servicing Air Cleaner Changing Engine Oil, Oil Filter, and Fuel Filter Stop engine and let coolClose valve and valve cap Before Adding Oil Running engine Adjusting Engine Speed Idle Speed AdjustmentWeld/Power Speed Adjustment Turn idle speed screw for fine ad- justments Stop engine. Disconnect negative − battery cable Overload ProtectionServicing Optional Spark Arrestor Fuse F1 See Section − Troubleshooting Welding TroubleshootingGenerator Power Troubleshooting Trouble Remedy Engine Troubleshooting Check receptacle wiring and connectionsErs SR2 and SR3 Check fuel level − Parts List Control switch S2, and throttle solenoid TS1Recommended Spare Parts Recommended Spare Parts − Electrical Diagrams Circuit Diagram For Welding Generator 240 424-B − Generator Power Guidelines Selecting Equipment Grounding When Supplying Building Systems How Much Power Does Equipment Require?Use ground device as stated Electrical codes Approximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Power Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 / Volts = Starting Amperage Typical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Stick Welding Procedure − Stick Welding Smaw GuidelinesWeld current starts when Electrode touches work Electrode and Amperage Selection Chart Striking an ArcScratch Technique Tapping Technique Poor Weld Bead Characteristics Good Weld Bead CharacteristicsPositioning Electrode Holder End View Of Work Angle Side View Of Electrode Angle 10-30 Conditions That Affect Weld Bead Shape Electrode Movement During WeldingElectrode Angle Normal Groove Butt Joints Lap JointTee Joint Or Less Troubleshooting Weld TestPossible Causes Corrective Actions Weld bead Lack of Penetration Good Penetration Good Penetration Excessive PenetrationMetal remains Direction SOCKET/WRENCH Selection Table Standard Metric Support ServiceAssistance Contact your Distributor for Hobart Welding Products

Hobart Welding Products OM-240 438E Changing Engine Oil, Oil Filter, and Fuel Filter, Up fuel

Models: OM-240 438E

8-4. Changing Engine Oil, Oil Filter, and Fuel Filter

! Stop engine and let cool.

Close valve and valve cap

before

adding

oil

running engine.

up fuel.