Holland BH421-AG4 manual Tighten

10 - 24 Carriage Bolt bolt must be inserted in slot of Lid Stop

FIGURE 5a

Lid Stop

Shelf

Flat Washer and “Top Lock” Nut

1/4 - 20 x 5/8 Hex Bolt and Lock Washer

Hinge

1/4 - 20 Hex Bolt and Lock Washer

10 - 24 x 1/2 Carriage Bolt

Insert Lid Stop into slot in Lid

FIGURE 5b

10 - 24 Top Lock Nut and flat Washer

Lid Stop

1/4 - 20 x 1 Round head Phillips Screw and Lock Washer

10 -24 x 1/2 Carriage Bolt

10 -24		FIGURE 7
Hex Nut	Thermometer
and Lock
Washer	Hole
cutaways for
clarity only
10 -24
Hex Nut
and Lock
Washer
	10 -24 x 1/2 Phillips
	Head Screw (8 plcs)

washer and “Top Lock” nut. Tighten the lock nut completely and then loosen it just enough to allow movement of the lid stop on the screw. Note: the “Top Lock” nut will be very tight on the screw when installing. This is normal. Repeat for the opposite side.

❍Position the shelf onto the brackets as shown. Using 10-24 x 1 carriage bolts, lock washers and nuts, fasten securely to brackets. Repeat for opposite side.

❍Bolt the 2 hinges to the grill bottom assembly using the 1/4-20 x 5/8 hex head bolts and lock washers. Do not fully tighten the hinges at this time.

❍Figure 5b Place the lid onto grill bottom assembly. Fasten the body hinges to the lid assembly using 1/4-20 x 5/8 hex head bolts and lock washers. Tighten all 8 hinge bolts completely.

❍Insert a 10-24 x 1/2 carriage bolt into the square hole in the lid end panel. Then while holding the carriage bolt in place, open the lid just enough to insert the lid stop through the slot in the lid end panel. Place the single hole in the lid stop over the carriage bolt. Secure with flat washer and “Top Lock” nut. Repeat for the opposite side. Note: the “Top Lock” nut will be very tight on the screw when installing. This is normal. Tighten the lock nut completely and then loosen it just enough to allow movement of the lid stop on the screw. Repeat for the opposite side.

Step 7.

Refer to Figure 7. Select the following items:

1.smoke stacks

2.handle and brackets

3.thermometer

❍Open the lid fully. Using the 10-24 x 1/2 round head Phillips screws, lock washers and hex nuts fasten the smoke stacks to the grill lid as shown. Tighten securely.

❍Install the thermometer through the small hole in the center of the lid near the smoke stacks. Using a 1/2” wrench,VERY GENTLY, snug thermometer securing nut. VERY IMPORTANT: DO NOT OVER-

TIGHTEN.

❍Select the two handle brackets and handle. First attach the brackets to the lid using 10-24 X 1/2 carriage bolts, lock washers and hex nuts. DO NOT FULLY TIGHTEN AT THIS TIME.

Step 6.

Refer to Figure 6. Select the following items:

1.shelf brackets (2 lt. 2 rt.)

2.shelves (2 ea.)

❍Select one of the shelf brackets and bolt it to the grill bottom end panel using 1/4-20 x 5/8 hex head bolts and lock washers. Tighten completely. Repeat for each of the 3 remaining brackets.

❍Now place tube handle between handle brackets and secure with 1/4- 20 X 1” round head Phillips screw and lock washer as shown. Tighten completely.

❍Now go back and tighten completely the handle brackets to lid

E-5