ASSEMBLY

UNPACKING

This product requires assembly.

Carefully cut the box down the sides then remove the machine and any accessories from the box. Make sure that all items listed in the packing list are included.

NOTE: This machine is heavy and requires a minimum of two people to lift. To avoid back injury, lift with your legs and not your back.

WARNING:

Do not attempt to modify this product or create acces- sories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious per- sonal injury.

WARNING:

Do not use this product if any parts on the Loose Parts List are already assembled to your product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury.

Inspect the unit carefully to make sure no damage oc- curred during shipping.

Do not discard the packing material until you have carefully­ inspected and satisfactorily operated the product­.

If any parts are damaged or missing, please call 1-800-242-4672 for assistance.

LOOSE PARTS LIST

See Figure 3.

Key

 

 

No.

Description

Qty.

1

Bolt (3/8-16 x 4-1/4 in.)

2

2

Washer (3/8 in.)

2

3

Spacer (.38 ID)

2

4

Wheel

2

5

Lock Nut (3/8-16)

2

6

Handle Lock Pin

1

7

Lanyard

1

8

Lock Nut (1/4-20)

2

9

Washer (1/4 in.)

2

10

Rubber Foot

2

11

Bolt (1/4-20 x 1-1/2 in.)

2

12

Flange Nut (5/16-18)

2

13

Washer (5/16 in.)

4

14

Bolt (5/16-18 x 1 in.)

2

15

Frame Support

1

16

Engine Lubricant

1

 

Operator’s Manual (not shown)

1

WARNING:

If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

WARNING:

Do not attempt to operate the generator until assembly is complete. Failure to comply could result in possible serious personal injury.

TOOLS NEEDED

See Figure 4.

The following tools (not included or drawn to scale) are needed for assembly:

7/16 in., 1/2 and 5/8 in. socket wrench

7/16 in., 1/2 and 5/8 in. combination wrench

NOTE:  Do not put fuel or lubricant in the generator before installing the feet, frame support, and wheels.

INSTALLING FEET ON THE FRAME SUPPORT

See Figure 5.

Locate the following items:

2 rubber feet

2 lock nuts (1/4-20)

2 washers (1/4 in.)

2 bolts (1/4-20 x 1-1/2 in.)

Insert bolt through foot, then through frame support as shown.

Thread washer over the bolt, then install nut. Tighten nut securely.

NOTE: Be careful not to overtighten so that foot mate- rial collapses.

Repeat with remaining foot.

INSTALLING THE FRAME SUPPORT

See Figure 5.

Install the frame support on the bottom of the generator frame on the same side as the handle.

Locate the following items: Frame support

2 flange nuts (5/16-18)

2 washers (5/16 in.)

2 bolts (5/16-18 x 1 in.)

Raise the end of the generator where the recoil starter is located high enough to gain access to the frame bottom; securely position props underneath to support.

Align the holes on the frame support with the holes on the generator frame.

Page 11 — English

Page 15
Image 15
Homelite UT903611 manuel dutilisation Assembly