F90A,B SELF-CONTAINED COMMERCIAL ELECTRONIC AIR CLEANER

Permanent Wiring

BOLT AND ￿

 

WASHER

WALL BRACKET

 

1.Loosen the two screws and remove the plate covering the wiring compartment.

2.Remove the power cord.

Cut the black and white wires of the power cord, leaving six inches from the electrical connector. Strip 1/2 in. (12 mm) insulation from the end of each wire.

Cut the green wire flush with the electrical connector.

Remove the power cord and strain relief bushing.

Install plug (provided) in the hole that contained the power cord.

3.Attach the conduit to the unit.

4.Run 3-strand, no. 14 wire through the conduit into the wiring compartment.

5.Wire the F90 using the wiring diagram shown in Fig. 12. Assure the green wire is secured to the green grounding screw provided.

6.Reinstall the wiring compartment plate and tighten the screws.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

MOUNT AS CLOSE￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TO CEILING AS￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POSSIBLE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REMOVE￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VENTURI￿

 

 

 

 

 

 

 

 

 

 

 

 

CELLS￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PLATE

 

 

 

 

 

 

 

 

 

 

 

 

AND￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LAG SCREW￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FILTERS￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BRACKETS TO￿

￿

NUT AND WASHER

 

 

 

 

 

 

 

 

 

 

 

 

WALL STUDS

 

 

 

 

 

 

 

 

 

1 REPLACE REAR LOUVERS WITH BLANK PLATE ON F90 SIDE￿

ADJACENT TO THE WALL.

M1536

Fig. 11. Mounting F90 using 118638C Mounting Kit.

CONDUIT

GREEN￿

(TO GROUND)

+

F90￿

GROUND ￿ SCREW

WHITE￿

FROM F90

WHITE

BLACK

 

BLACK￿

FROM F90

M1529

Fig. 12. Wiring F90.

Installing Activated Carbon Filters, Cells, and Prefilters

1.Insert the activated carbon filters (if used) into the channel guides closest to the fan.

2.Inspect the cells for broken ionizer wires and bent collector plates. Moderately bent or warped collector plates can be bent back into shape. Broken ionizer wires must be replaced for top efficiency as instructed on page 15.

3.Insert the cells into the channel guides until they touch the back stop of the F90. Assure the cell airflow arrow is pointing toward the fan. In this position, the ionizer wires are facing downward (away from the fan).

4.Insert the prefilters into the channel guides until they touch the back of the channels.

11

68-0103-6 Revised 11-07

Page 11
Image 11
Honeywell F90B, F90A specifications Installing Activated Carbon Filters, Cells, and Prefilters, Permanent Wiring