Message | Explanation and/or corrective action | Level | |
|
|
| |
|
|
| |
| The registry read failed. The registry information read when this message is logged is the |
| |
Registry read failure | application information. It the Administration key cannot be opened or if the AppName | LOG_ERROR | |
value is missing or empty, this error is logged. The other application information is not | |||
|
| ||
| required. If the AppName value is not available, AppLock cannot switch into user mode. |
| |
|
|
| |
Reset system work area | The system work area is adjusted when in user mode to cover the taskbar area. The |
| |
system work area has to be adjusted to exclude the taskbar area in administration mode. | LOG_ERROR | ||
failure | |||
AppLock was unable to adjust this area. |
| ||
|
| ||
|
|
| |
Shift pressed | The Shift key has been pressed and trapped by the HotKey processing. | LOG_EX | |
|
|
| |
Shift | Processing the hotkey and backdoor entry | LOG_EX | |
|
|
| |
Show taskbar | The taskbar is now being made visible and enabled. | LOG_ | |
PROCESSING | |||
|
| ||
|
|
| |
Switching to admin- | The system is currently in user mode and is now switching to admin mode. The switch | LOG_ | |
backdoor | occurred because of the backdoor key presses were entered by the administrator. | PROCESSING | |
|
|
| |
Switching to admin- | The system is currently in user mode and is now switching to admin mode. The switch | LOG_ | |
hotkey press | occurred because of a hotkey press by the administrator. | PROCESSING | |
|
|
| |
Switching to admin- | The keyboard hook load failed, so AppLock switches to admin mode. If a password is | LOG_ | |
specified, the password prompt is displayed and remains until a valid password is | |||
kbdhook.dll not found | PROCESSING | ||
entered. | |||
|
| ||
|
|
| |
Switching to admin- | If the keyboard hook initialization fails, AppLock switches to admin mode. If a password is | LOG_ | |
keyboard hook | specified, the password prompt is displayed and remains until a valid password is | ||
PROCESSING | |||
initialization failure | entered. | ||
| |||
|
|
| |
Switching to admin- | See the explanation of the “Registry read failure” above. AppLock is switching into Admin | LOG_ | |
mode. If a password has been configured, the prompt will be displayed and will not be | |||
registry read failure | PROCESSING | ||
dismissed until a valid password is entered. | |||
|
| ||
|
|
| |
Switching to | In administration mode, the taskbar is visible and enabled. | LOG_EX | |
TaskbarScreenMode | |||
|
| ||
|
|
| |
Switching to user mode | The registry was successfully read and AppLock is starting the process to switch to user | LOG_ | |
mode. | PROCESSING | ||
| |||
|
|
| |
Switching to | The system is currently in admin mode and is now switching to user mode. The switch | LOG_ | |
press | occurred because of a hotkey press by the administrator. | PROCESSING | |
|
|
| |
Taskbar hook failure | AppLock is unable to control the taskbar to prevent the locked application from re- | LOG_ERROR | |
enabling it. | |||
|
| ||
|
|
| |
Taskbar hook OK | AppLock successfully installed control of the taskbar. | LOG_EX | |
|
|
| |
Timeout looking for app | After the application is launched, AppLock must wait until the application has initialized |
| |
itself before proceeding. The application did not start successfully and AppLock has timed | LOG_ERROR | ||
window | |||
out. |
| ||
|
| ||
|
|
| |
ToUser after admin, not | The user mode switch is attempted when the device boots and after the administrator | LOG_EX | |
at boot | presses the hotkey. The mode switch is being attempted after a hotkey press. | ||
| |||
|
|
| |
ToUser after | The switch to user mode is being made via a hotkey press and the administrator has left | LOG_EX | |
still open | the application open and has not made any changes in the configuration. | ||
| |||
|
|
| |
ToUser after | If user mode is being entered via a hotkey press, the administrator may have left the |
| |
configured application open. If so, AppLock does not launch the application again unless | LOG_EX | ||
app or cmd line change | |||
a new application or command line has been specified; otherwise, it just locks it. |
| ||
|
| ||
|
|
| |
| The desktop is moved when switching into user mode. This prevents them from being |
| |
Unable to move desktop | visible if the application is exited and restarted by the timer. This error does not affect the | LOG_ERROR | |
| screen mode switch; processing continues. |
| |
|
|
|