Troubleshooting
| Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance | |||
EN | ||||
(see Assistance). |
| |||
|
|
|
| |
|
|
|
| |
|
| Problem: | Possible causes / Solutions: | |
|
|
|
| |
|
| The dishwasher does not start or | • Switch off the appliance by pressing the ON/OFF button, switch it back on after | |
|
| cannot be controlled | approximately one minute and reset the program. | |
|
|
| • The appliance has not been plugged in properly. | |
|
|
| • The dishwasher door has not been shut properly. | |
|
|
|
| |
|
| The door won’t close | • The lock was released. Strongly push the door until a “clacking” noise is heard. | |
|
|
|
| |
|
| No water drains out from the | • The dishwasher cycle has not yet finished. | |
|
| dishwasher. | • The water inlet hose is bent (see Installation). | |
|
|
| • The drain duct is blocked. | |
|
|
| • The filter is clogged up with food residues. | |
|
|
|
| |
|
| The dishwasher makes excessive | • The dishes are rattling against each other or against the sprayer arms. | |
|
| noise. | • An excessive amount of foam has been produced: the detergent has not been | |
|
|
| measured out correctly or it is not suitable for use in dishwashers (see | |
|
|
| and use). | |
|
|
|
| |
|
| The dishes and glasses are | • The level of the refined salt is low or the dosage setting is not suited to the | |
|
| covered in a white film or | hardness of the water (see Rinse aid and salt). | |
|
| limescale deposits. | • The lid on the salt dispenser is not closed properly. | |
|
|
| • The rinse aid has been used up or the dosage is too low. | |
|
|
|
| |
|
| The dishes and glasses are | • The rinse aid dosage is too high. | |
|
| streaked or have a bluish tinge. |
| |
|
|
|
| |
|
| The crockery has not been dried | • A wash cycle without a drying program has been selected. | |
|
| properly. | • The rinse aid has been used up or the dosage is too low (see Rinse aid and | |
|
|
| salt). | |
|
|
| • The rinse aid dispenser setting is not suitable. | |
|
|
| • The crockery is made from | |
|
|
|
| |
|
| The dishes are not clean. | • The racks are overloaded (see Loading the racks). | |
|
|
| • The crockery has not been arranged well. | |
|
|
| • The sprayer arms cannot move freely. | |
|
|
| • The wash cycle is too gentle (see Wash cycles). | |
|
|
| • An excessive amount of foam has been produced: the detergent has not been | |
|
|
| measured out correctly or it is not suitable for use in dishwashers (see | |
|
|
| and use). | |
|
|
| • The lid on the rinse aid compartment has not been shut correctly. | |
|
|
| • The filter is dirty or blocked (see Care and maintenance). | |
|
|
| • The refined salt level is low (see Rinse aid and salt). | |
|
|
|
| |
|
| The dishwasher does not take any | • There is no water in the mains supply. | |
|
| water in - Tap | • The water inlet hose is bent (see Installation). | |
|
| (several short beeps are emitted) | • Turn on the tap and the appliance will start after a few minutes. | |
|
| (the ON/OFF indicator light flashes | • The appliance lock has been activated because no action was taken when the | |
|
| and the number 6 appears on the | beeps sounded. | |
|
| display). | Switch off the appliance using the ON/OFF button, turn on the tap and switch | |
|
|
| the appliance back on after 20 seconds by pressing the same button. Re- | |
|
|
| program the appliance and restart the wash cycle. | |
|
|
|
| |
|
| Water inlet hose alarm / Water inlet | • Switch off the appliance by pressing the ON/OFF button. Shut off the water tap | |
|
| filter blocked | to eliminate the risk of flooding and remove the plug from the electrical socket. | |
|
| (the ON/OFF indicator light flashes | Make sure the water inlet filter has not become blocked by impurities (see “Care | |
|
| and the number 7 appears on the | and maintenance” chapter). | |
|
| display). |
| |
|
|
|
|
*Only available in selected models.
14