For a WAN Port, For an Fddi Port | HP 445 manual

Cables and Connectors

Cable and Connector Pin-Outs

For a WAN Port

HP part number 28606-63007; pin

connections:

pin 9 to pin 23

pin 10 to pin 27

pin 11 to pin 50

pin 12 (not used) to pin 7 (not used)

pin 13 (not used) to pin 49 (not used) pin 14 to pin 19

pin 15 to pin 4

pin 16 to pin 46

pin 17 to pin 1

pin 21 to pin 20

pins 30, 31, and 32 to pin 27

pins 33 and 34 (not used) to pin 29 (not used)

pin 35 to pins 40 and 39

pin 36 to pin 25

pin 37 to pin 26

pin 38 to pin 22

pin 42 to pin 41

pin 47 (not used) to pin 24

pin 51 to pin 2

pin 53 (not used) to pin 8 (not used)

pin 54 (not used) to pin 29 (not used)

pin 55 (not used) to pin 8 (not used)

pin 56 to pin 3

pin 57 to pin 28 (not used)

pin 58 to pin 6

pin 59 to pin 48 (not used)

For an FDDI Port

HP part number 5063-2490

FDDI-standard loopback connector

Cables and A Connectors

A-21

Image 110

HP 445 manual For a WAN Port, For an Fddi Port, HP part number FDDI-standard loopback connector

Contents

HP AdvanceStack Routers Installation Guide Installation Guide Preface Preface Contents Troubleshooting Fddi Cable Attachment Configurations Installation and Initial Setup Installation Phase 1 Ensure that You Have a Complete Set of Accessories Phase 2 Prepare the Network Smds individual address T e Phase 3 Prepare the Router Hardware Mount the Router Single-Height Models These models are 4.3 cm 1.7inches in height Double-Height Models These models are 8.9 cm 3.5 inches in height Connect a Console Optional When Is a Console Necessary?To install a console Attach Network Cables Connecting a LAN to the AUI Interface Transceiver from supporting the weight of the router 10. Installing the AUI Retainer Improperly grounded LAN cable, ensure that the LAN cable is Connecting a LAN to the BNC InterfaceTo avoid an electrical shock hazard due to an ungrounded or This manual Other side of the ‘‘T’’ connector Each coaxial cable segment must be terminated with a 50-ohm Connecting a LAN to the Token Ring Interface 15. LAN 802.5 Token Ring Connection Connecting an Fddi Ring to the Fddi Interface 16. Connecting Fddi Without a Bypass Switch Using an Optional Bypass Switch to Connect an Fddi Ring Installation Disconnect the router from any directly connected Fddi ring Fddi ring, refer to the instructions for your bypass switchBypass switch Connect the bypass cables to the Fddi ports as shown above Attach the male end of the cable to the router’s WAN port Connecting a WAN to the WAN InterfaceHand-tighten the screws attached to the cable connector Equipment Plug In and Verify the Router Hardware Bridging mode due to some unforseen problem, there may beFirst time or clearing the router to the factory default Correct ac voltage range for your power source Saved After the Self-test LED turns off Router’s console port, either directly or through a modem Two or three times PasswordTroubleshooting Main menu screen then appears Phase 4 Initialize and Verify Router 24. The Main Menu Create or Modify a Router Configuration Shortest Path to a Functioning Configuration An Overview of Your Configuration Tools Boot the Router To boot the router now Defaultconfig boot Return Press Y to commence the reboot operation 26. The Copyright Screen Set the Correct Time and Date Optional If the router will operate as a Set Manager and User Passwords Optional Setting a Password At the prompt, type Network links are operational Verify Router InitializationThat the following two conditions exist All networks can be reached by the router Examine the Event Log 29. The Event Log Line in the Main Menu Phase 4 Initialize and Verify the Router 30. Example of the Statistics Screen Menu Following service statistics screens are available Examine the Bridging and Routing Tables Phase 4 Initialize and Verify the Router Destination Test Node AccessibilityTesting Node Accessibility Features and General Hardware Operation Features Features Router Ports Additional Features Interpreting Front-Panel LEDs Example of Router Front Interpreting Back-Panel LEDs Fan outlet Example of Port Status LEDs for an Fddi Port Fault is always lit while the Reset button is pressed Meanings of Router Status LEDs Not all port types appear on all routers Net Fail Amber LED The Net Fail LEDs serve two functions All Net Fail LEDs are lit while the Reset button is pressed Fddi Port Thru Optical Bypass Enabled green Testing the LEDs Location of the Reset and Clear Buttons When you press and release the Reset button there may be a To Reset the RouterResetting does not affect any current passwords LEDs for the error, and turn to , ‘‘Troubleshooting’’ To Clear the Manager and User Passwords To Clear the Router Again Reset-Clear combination erases the current configurationDisplay the Main menu -24 on Initialization Sequence Troubleshooting Introducing Router Troubleshooting Features Basic Troubleshooting Tips Interpreting LED Error Patterns LED Error Patterns During Initialization LED Error Patterns During Operation General Procedure for Self-Test Failures Error number Recoverable Self-Test Failures Non-Recoverable Self-Test Failures Verifying LED Operation on Other Router Models Verifying LED OperationVerifying LED Operation on the HP Router ER, TR, and SR Diagnostic Tests Testing the Router Only To test a LAN port 802.3/Ethernet or 802.5/token ring Testing the Router’s PortsTo test a WAN port To test an Fddi port Troubleshooting a Terminal or Modem ConnectionReset Speed Sensing To test the router’s console port Switch the terminal or PC’s power off and then on once Adjust Baud RateReset the Terminal Provider for further assistance To resume after testing, remove the loopback connector Loopback Connectors on page A-20Press the Reset button on the back of the router Check the Configuration Loopback test switch, enable it for the test Switch that must be set to correspond to these requirementsInformation on the Xcvr Signal Polling parameter, refer to Router’s port is faulty Testing a Link Tests from Other Devices ∙ For Fddi circuits HP Router BR only Get cct.fddi-name.ieee.addr Return Ping Ping Ping x.x.x.x count Ping x.x.x.x count wait Telnet Telnet Cables and Connectors Cables and Connectors Cables and a Connectors HP Cables Standard Cable or Cable Solution Other Standard Cables RS-232 Modem Cable-Minimum Pin-Outs Cable and Connector Pin-OutsRouter Console Port Connector Pin-Outs Terminal/PC end Router end Pin female Null-Modem Adapter for Use with Modem Cable-Minimum Pin-Outs Terminal or in your terminal emulation program Router AUI LAN Port Definition AUI Cable-Minimum Pin-Outs RS-449/422 WAN Cable-Minimum Pin-Outs Pin male Circuit WAN Cable-Minimum Pin-Outs WAN Cable-Minimum Pin-Out RS-232 WAN Cable-Minimum Pin-Outs Maximum cable length is 15 meters 50 feet Back-to-Back Test Cables Two test cables available are RDA RDB and so on, must be twisted pairs of wire For the pinouts of this cable, turn RDB, and so on must be twisted pairs of wire Pin Definition of Token Ring Connector Router Token Ring/802.5 LAN Port Definition Fddi Optical Bypass DIN Connector Pinouts HP Part Number Figure A-2. Fddi Bypass Mini DIN Connector Pinouts Fddi Cable Figure A-3. Example of Fddi Cable For an AUI LAN Port Loopback ConnectorsFor the Console Port For a Token Ring/802.5 Port For an Fddi Port HP part number FDDI-standard loopback connectorFor a WAN Port Modem Configuration HP 50759A Support Link HP 35031A Support LinkHP 37212B Support Link Black Box V.32 9600 Async Configuration ModemHayes 2400 Smartmodem Specifications Power Consumption Physical without brackets Electromagnetic Emissions SpecificationsEnvironmental Acoustical for Germany Data Communications Specifications Cable Interfaces Specifications Specifications Fddi Cable Attachment Configurations Fddi Cable Attachment Configurations Dual-Attach Station DAS Figure D-1. Example of Dual-Attach Station Connections Single-Attach Station SAS Figure D-2. Example of Single-Attach Station Connections Dual-Homed Connection Figure D-3. Example of Dual-Homed Connection Safety Information Safety InformationSafety Symbols Grounding Symboles de sécurité Informations concernant la sécurité Sicherheitssymbole Hinweise zur Sicherheit Considerazioni sulla sicurezza Simboli di sicurezza Consideraciones sobre seguridad Símbolos de seguridad Safety Information Regulatory Statements and Warranty Applies to HP Router PR, FR, TFR, LR, and BR European CommunityVcci Class 1 Japan Only For the HP Router PR/FR/TFR/LR/BR Warranty Regulatory Statements Declarations of Conformity Regulatory Statements and Warranty Three-Year Limited Hardware Warranty Regulatory Statements and Warranty Software or Firmware Warranty Index Index Index Time ...1-33 communications standards ...C-4 compatibility Optical bypass not needed ...D-4 -- D-5 port testing Fget MIB variables See Fddi Modem ...1-10, 1-21, A-3 A-5, A-7, B-1 B-3 Resetting, caution ...3-14 restart Manager ...1-31, 1-35, 2-17 resetRemote signal & sense ...2-9, 3-5 remote terminal Rx LED Safety Safety approvals ...C-4 Time protocol service SpecificationsSpeed sense, reset Summary, installation Weight ...C-2 Manual Part Number