Manuals / HP / Computer Equipment / Laptop

HP B1223TU, B1201VU, B1203VU, B1200, B1205VU, B1204VU, B1298TU manual Removal and replacement procedures

Models: B1225TU B1205VU B1283TU B1227TU

1 146

Page 64

56 Chapter 4 Removal and replacement procedures

10. If it is necessary to replace the display bezel or the display assembly internal components, remove the six rubber screw covers (1) and the six Torx T8M2.5×6.0 screws (2) that secure the display bezel to the display enclosure.

NOTE: See Camera module on page 38 for camera module removal information.

11. Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the display bezel until the bezel disengages from the display enclosure.

12. Remove the display bezel (3). The display bezel is available using spare part number 454399-001.

13. If it is necessary to replace the display inverter, release the inverter (1) as far as the display panel cable and backlight cable allow.

56 Chapter 4 Removal and replacement procedures

Page 64

Image 64

HP B1223TU, B1201VU, B1203VU, B1200, B1205VU, B1204VU, B1298TU, B1250TU, B1244TU, B1245TU manual Removal and replacement procedures

Contents

Maintenance and Service Guide Compaq Presario B1200 Notebook PCCopyright 2007 Hewlett-Packard Development Company, L.P Safety warning notice iv Safety warning notice Table of contents Removal and replacement procedures1 Product description 2 External component identification Illustrated parts catalogSpecifications Setup UtilityScrew listing 8 Backup and Recovery 9 Connector pin assignmentsPower cord set requirements RecyclingPage Category 1 Product descriptionDescription Category 2 Chapter 1 Product descriptionDescription Category Integrated personal area network PAN options by way of BluetoothDescription Serviceability 4 Chapter 1 Product descriptionCategory Description2 External component identification Display componentsComponent DescriptionTop components Pointing devicesComponent FunctionButtons Control Panel System and MaintenancePower Options ComponentKeys ComponentFunction esc keyComponent LightsDescription Blinking The volume scroll zone is being used to decrease 10 Chapter 2 External component identificationComponent DescriptionFront components Produces sound when connected to optional powered stereoComponent FunctionLeft-side components 12 Chapter 2 External component identificationComponent FunctionRight-side components ComponentFunction Connects an optional S-Video device such as a televisionBottom components 14 Chapter 2 External component identificationComponent Function3 Illustrated parts catalog Serial number locationComputer major components 16 Chapter 3 Illustrated parts catalogRTC battery Speaker assemblyBluetooth module Description18 Chapter 3 Illustrated parts catalog DescriptionSpare part numberDescription Spare partnumber Broadcom 802.11a/b/g WLAN modules20 Chapter 3 Illustrated parts catalog Item DescriptionSpare part numberCable Kit Item DescriptionSpare part number Cable KitPlastics Kit Item DescriptionSpare part number Plastics KitMass storage devices Item DescriptionSpare part number DescriptionMiscellaneous parts 24 Chapter 3 Illustrated parts catalogDescription Spare part numberSequential part number listing Spare part Description number26 Chapter 3 Illustrated parts catalog Spare part Description numberSequential part number listing Spare partDescription number28 Chapter 3 Illustrated parts catalog Spare partDescription number4 Removal and replacement procedures Preliminary replacement requirementsService considerations Tools requiredCables and connectors Drive handlingGrounding guidelines Electrostatic discharge damagePackaging and transporting guidelines Workstation guidelinesMaterial Equipment guidelinesVoltage protection level Unknown user password Component replacement procedures Serial numberComputer feet 36 Chapter 4 Removal and replacement proceduresBattery Camera module 7. Disconnect the camera module cable 2 from the camera module Component replacement procedures8. Remove the camera module and bracket 40 Chapter 4 Removal and replacement procedures Reverse this procedure to reassemble and install the camera module10. Remove the camera module bracket 2 from the camera module Hard drive Reverse this procedure to reassemble and install the hard drive 42 Chapter 4 Removal and replacement procedures6. Remove the hard drive 4 from the hard drive bay 8. Lift the bracket 2 straight up to remove it from the hard driveMemory module Reverse this procedure to install a memory module 44 Chapter 4 Removal and replacement proceduresDescription WLAN moduleSpare part number 4. Remove the battery see Battery on page Remove the WLAN module 46 Chapter 4 Removal and replacement proceduresBefore removing the WLAN module, follow these steps 2. Disconnect all external devices connected to the computerReverse this procedure to install the WLAN module Component replacement proceduresOptical drive Component replacement procedures Reverse this procedure to reassemble and install an optical drive7. Remove the optical drive bracket Keyboard 8. Remove the keyboard Reverse this procedure to install the keyboard Component replacement proceduresSwitch cover 6. Remove the switch cover Reverse this procedure to install the switch coverComponent replacement procedures 5. Disconnect the LED board cable 1 from the system boardDisplay assembly 9. Lift the display assembly 2 straight up and remove it Component replacement procedures5. Disconnect the display panel cable 1 from the system board 6. Disconnect the camera cable 2 from the system board56 Chapter 4 Removal and replacement procedures Component replacement procedures 17. Remove the display panel 2 from the display enclosureReverse this procedure to reassemble and install the display assembly 58 Chapter 4 Removal and replacement proceduresd. Switch cover see Switch cover on page e. Display assembly see Display assembly on pageTop cover a. Hard drive see Hard drive on page60 Chapter 4 Removal and replacement procedures 2. Remove the following2 Seven Phillips PM2.5×7.0 screws 3 Three Phillips PM2.0×3.0 screws 3. Turn the computer right-side up, with the front toward youComponent replacement procedures Reverse this procedure to install the top cover7. Lift the top cover 3 straight up and remove it RTC battery f. Top cover see Top cover on paged. Switch cover see Switch cover on page e. Display assembly see Display assembly on pageReverse this procedure to install the RTC battery 2. Remove the RTC batteryComponent replacement procedures Front LED board d. Switch cover see Switch cover on pagee. Display assembly see Display assembly on page a. Hard drive see Hard drive on pageBluetooth module d. Switch cover see Switch cover on pagea. Hard drive see Hard drive on page b. Optical drive see Optical drive on pagee. Display assembly see Display assembly on page Speaker assemblyf. Top cover see Top cover on page d. Switch cover see Switch cover on page 4. Remove the battery see Battery on pagea. Hard drive see Hard drive on page g. Bluetooth module see Bluetooth module on page Microphoned. Switch cover see Switch cover on page e. Display assembly see Display assembly on pageExpressCard assembly see ExpressCard assembly on page System boardMemory module see Memory module on page WLAN module see WLAN module on pageReverse this procedure to install the system board 70 Chapter 4 Removal and replacement proceduresExpressCard assembly h. System board see System board on paged. Switch cover see Switch cover on page e. Display assembly see Display assembly on page4. Remove the ExpressCard assembly from the system board Reverse this procedure to install the ExpressCard assembly72 Chapter 4 Removal and replacement procedures 3. Turn the system board right-side up, with the left side toward youModem module d. Switch cover see Switch cover on pagee. Display assembly see Display assembly on page g. Bluetooth module see Bluetooth module on page74 Chapter 4 Removal and replacement procedures 4. Remove the modem module and modem module cabled. Switch cover see Switch cover on page e. Display assembly see Display assembly on pageg. Bluetooth module see Bluetooth module on page a. Hard drive see Hard drive on page76 Chapter 4 Removal and replacement procedures Reverse this procedure to install the fan4. Remove the fan 3 from the heat sink Heat sink h. System board see System board on page i. Fan see Fan on paged. Switch cover see Switch cover on page e. Display assembly see Display assembly on page78 Chapter 4 Removal and replacement procedures Reverse this procedure to install the heat sink3. Remove the heat sink 3 by lifting it straight up Processor d. Switch cover see Switch cover on pagee. Display assembly see Display assembly on page g. Bluetooth module see Bluetooth module on pagei. Fan see Fan on page j. Heat sink see Heat sink on page Remove the processorStarting the Setup Utility 5 Setup UtilityChanging the language of the Setup Utility Navigating and selecting in the Setup Utility Restoring default settings in the Setup Utility2. Select Exit Load Setup Defaults, and then press enter Displaying system informationUsing advanced Setup Utility features Closing the Setup UtilitySetup Utility menus Main menuSystem Configuration menu Diagnostics menuSecurity menu SelectComputer specifications 6 SpecificationsMetric 12.1-inch, WXGA display specifications 86 Chapter 6 SpecificationsMetric MetricHard drive specifications 200-GB160-GB 120-GBDVD/CD-RW Combo Drive specifications 88 Chapter 6 SpecificationsDVD-ROM Drive System DMA specifications 90 Chapter 6 SpecificationsHardware DMA System functionHardware IRQ System interrupt specificationsSystem function System I/O address specifications 92 Chapter 6 SpecificationsSystem function shipping configuration I/O address hexSystem function shipping configuration System I/O address specificationsI/O address hex System memory map specifications 94 Chapter 6 SpecificationsSize Memory address7 Screw listing Phillips PM2.0×4.0 screw96 Chapter 7 Screw listing Where used 3 screws that secure the fan to the heat sink Phillips PM2.0×4.0 screwWhere used Phillips PM2.0×5.0 captive screwColor QuantityPhillips PM2.5×12.0 captive screw ColorQuantity LengthPhillips PM3.0×4.0 screw ColorQuantity LengthPhillips PM2.5×4.0 screw ColorQuantity LengthWhere used 2 screws that secure the modem module to the system board Where used 2 screws that secure the top cover to the base enclosure102 Chapter 7 Screw listing Phillips PM2.5×7.0 screw Where usedColor QuantityWhere used 7 screws that secure the top cover to the base enclosure Where used 3 captive screws that secure the keyboard to the computer104 Chapter 7 Screw listing Where used 2 screws that secure the top cover to the base enclosure Phillips PM2.5×7.0 screwPhillips PM2.0×3.0 screw ColorQuantity LengthPhillips PM2.0×3.0 screw Phillips PM2.5×5.0 screw ColorQuantity LengthTorx T8M2.5×6.0 screw ColorQuantity LengthTorx T8M2.5×5.0 screw ColorQuantity LengthPhillips PM2.5×6.0 screw ColorQuantity LengthPhillips PM2.0×6.0 screw ColorQuantity LengthPhillips PM2.0×6.0 shoulder screw ColorQuantity Length8 Backup and Recovery Recovering system informationWhen to back up Backing up your informationUsing system restore points When to create restore pointsCreate a system restore point 1. Select Start Control Panel System and Maintenance SystemCreating recovery discs Restore to a previous date and time1. Select Start All Programs Recovery Manager Recovery Manager 3. Click Recovery disc creation, and then click NextReinstalling preinstalled programs and drivers Reinstalling software programs and driversa. Select Start Control Panel Programs Uninstall a program Performing a recovery Recovering from the recovery discsRecovering from the partition on the hard drive Select Start All Programs Recovery Manager Recovery ManagerDeleting the recovery partition on the hard drive Updating reinstalled software2. Select Start All Programs Recovery Manager Recovery Manager 4. Click Remove recovery partition, and then click Next9 Connector pin assignments Audio-out headphoneAudio-in microphone SignalSignal External monitorExternal monitor 122 Chapter 9 Connector pin assignments RJ-11 modemSignal Signal RJ-45 networkRJ-45 network 124 Chapter 9 Connector pin assignments S-Video-outSignal Signal Universal Serial BusUniversal Serial Bus 10 Power cord set requirements Requirements for all countries and regionsRequirements for specific countries and regions Country/regionAccredited agency Applicable note number11 Recycling BatteryDisplay 3. Remove the display bezel Perform the following steps to disassemble the display assemblyDisplay 7. Turn the display panel assembly upside down 6. Remove the display panel assembly 2 from the display enclosure130 Chapter 11 Recycling 10. Remove the display panel frame 2 from the display panel 12. Lift the top edge of the backlight cover 2 and swing it outward13. Remove the backlight cover 14. Turn the display panel right-side up17. Remove the backlight frame from the display panel 16. Turn the display panel upside down132 Chapter 11 Recycling 18. Remove the backlight from the backlight frame 19. Disconnect the display panel cable 1 from the LCD panel21. Release the LCD panel 3 from the display rear panel 23. Remove the LCD panel 24. Recycle the LCD panel and backlightIndex ExpressCard assembly volume muteEthernet, product description memory module compartmentPage