Manuals / HP / Computer Equipment / Laptop

HP 2000, D1E80UA Turn the computer right-side up, with the front toward you, Open the computer

Models: 2000

1 115

Download 115 pages 52.59 Kb

Page 61

6.Turn the computer right-side up, with the front toward you.

4.Remove the seven Phillips PM2.5×6.0 screws in the battery bay and the hard drive bay that secure the top cover to the computer.

5.Remove the two Phillips PM2.5×9.0 screws (1) and the three Phillips PM2.0×3.0 screws (2) in the battery bay that secure the top cover to the computer.

6.Turn the computer right-side up, with the front toward you.

7.Open the computer.

8.Release the ZIF connectors to which the following cables are attached, and then disconnect the cables from the system board:

●Power button board cable (1) (included with the power button board spare part kit, spare part number 646129-001)

●TouchPad button board cable (2) (included with the TouchPad button board spare part kit, spare part number 646130-001)

●TouchPad cable (3) (included in the Cable Kit, spare part number 646119-001)

Component replacement procedures 53

Image 61

HP 2000 Turn the computer right-side up, with the front toward you, Open the computer, Component replacement procedures

Contents

HP 2000 Notebook PC Maintenance and Service Guideits proprietor Copyright 2011 Hewlett-Packard Development Company, L.PFourth Edition December First Edition March Document Part Number Safety warning notice iv Safety warning notice 4 Removal and replacement procedures Table of contents1 Product description External component identificationPackaging and transporting guidelines 8 Power cord set requirements 7 Backup and recovery9 Recycling IndexPage equipped with an AMD 1 Product descriptionComputer models 2 Chapter 1 Product descriptionequipped with an Category 4 Chapter 1 Product description Category 6 Chapter 1 Product description Display 2 External component identificationChapter 2 External component identification ButtonKeys Keysesc key fn key10 Chapter 2 External component identification LightsTouchPad TouchPadrefer to the Regulatory, Safety, and Left side12 Chapter 2 External component identification Environmental NoticesRight side Right side14 Chapter 2 External component identification Bottom3 Illustrated parts catalog Service tag16 Chapter 3 Illustrated parts catalog Computer major components Computer major componentsSpare part number 18 Chapter 3 Illustrated parts catalog For use only with computer models equipped with an AMD E450 1.65-GHz processor 20 Chapter 3 Illustrated parts catalog BatteryComponent Spare part numberComputer major components 22 Chapter 3 Illustrated parts catalog Display assembly subcomponentsCable Kit Cable Kit24 Chapter 3 Illustrated parts catalog Mass storage devicesMiscellaneous parts Miscellaneous parts26 Chapter 3 Illustrated parts catalog Plastics KitSequential part number listing Sequential part number listingSpare part number 28 Chapter 3 Illustrated parts catalogDescription Sequential part number listing Spare part number 30 Chapter 3 Illustrated parts catalogDescription Spare part number Sequential part number listingDescription Spare part number 32 Chapter 3 Illustrated parts catalogDescription Preliminary replacement requirements 4 Removal and replacement proceduresService considerations Cables and connectorsDrive handling Grounding guidelinesElectrostatic discharge damage Event Typical electrostatic voltage levelsWorkstation guidelines Packaging and transporting guidelinesMaterial Equipment guidelinesVoltage protection level Service tag Component replacement proceduresComputer feet BatteryOptical drive select models only Component replacement procedures 4. Remove the battery see Battery on page Remove the optical drive42 Chapter 4 Removal and replacement procedures Reverse this procedure to reassemble and install the optical drive9. Remove the optical drive bracket WLAN module 44 Chapter 4 Removal and replacement procedures Reverse this procedure to install the WLAN moduleMemory module Hard drive Component replacement procedures 4. Disconnect the hard drive connector cable 1 from the system board7. Remove the hard drive 48 Chapter 4 Removal and replacement procedures Reverse this procedure to reassemble and install the hard driveKeyboard Remove the keyboard 50 Chapter 4 Removal and replacement procedures2. Rest and secure the computer on its left side 3. Partially open the computerTop cover Page 6. Turn the computer right-side up, with the front toward you Component replacement procedures7. Open the computer TouchPad cable 3 included in the Cable Kit, spare part number54 Chapter 4 Removal and replacement procedures Optical drive see Optical drive select models only on page Power button boardKeyboard see Keyboard on page Top cover see Top cover on page Optical drive see Optical drive select models only on page TouchPad button boardKeyboard see Keyboard on page Top cover see Top cover on page Component replacement procedures Reverse this procedure to install the TouchPad button board and cable4. Remove the TouchPad button board 4 and cables from the top cover Optical drive see Optical drive select models only on page USB boardKeyboard see Keyboard on page Top cover see Top cover on page USB board see USB board on page Power connector cableOptical drive see Optical drive select models only on page Keyboard see Keyboard on page Top cover see Top cover on pageOptical drive see Optical drive select models only on page SpeakersKeyboard see Keyboard on page Top cover see Top cover on page USB board see USB board on pageOptical drive see Optical drive select models only on page Optical drive connector cableKeyboard see Keyboard on page Top cover see Top cover on page DescriptionSpare part number Display assemblyWLAN module see WLAN module on page Keyboard see Keyboard on page Power connector cable see Power connector cable on pageTop cover see Top cover on page USB board see USB board on page Remove the display assemblyb. Disconnect the module cable 2 from the module 64 Chapter 4 Removal and replacement procedures7. If it is necessary to replace the hinge covers Component replacement procedures8. If it is necessary to replace the display panel 66 Chapter 4 Removal and replacement procedures9. If it is necessary to replace the display hinges Component replacement procedures10. If it is necessary to replace the display panel cable 68 Chapter 4 Removal and replacement proceduresSystem board RTC battery see RTC battery on page Display assembly see Display assembly on pageFan and heat sink see Fan/heat sink assembly on page Memory module see Memory module on pageComponent replacement procedures Reverse this procedure to install the system boardSystem board see System board on page RTC batteryPower connector cable see Power connector cable on page Display assembly see Display assembly on pageFan/heat sink assembly Display assembly see Display assembly on page Power connector cable see Power connector cable on pageOptical drive see Optical drive select models only on page WLAN module see WLAN module on page Keyboard see Keyboard on pageComponent replacement procedures Remove the fan/heat sink assembly1. Disconnect the fan cable from the system board 2. Turn the system board upside down, with the front toward you76 Chapter 4 Removal and replacement procedures Component replacement procedures 78 Chapter 4 Removal and replacement procedures Component replacement procedures Hard drive see Hard drive on page ProcessorOptical drive see Optical drive select models only on page WLAN module see WLAN module on page Keyboard see Keyboard on page Top cover see Top cover on page System board see System board on page2. Lift the processor 2 straight up, and then remove it Using Setup Utility 5 Setup Utility BIOS and System DiagnosticsStarting Setup Utility Changing the language of Setup UtilityDisplaying system information Navigating and selecting in Setup UtilityExiting Setup Utility Restoring factory settings in Setup UtilityUpdating the BIOS Downloading a BIOS update Determining the BIOS version1. Windows 7-Select Start Help and Support Maintain Using System Diagnostics Computer specifications 6 Specifications88 Chapter 6 Specifications 15.6-inch display specificationsHard drive specifications Hard drive specificationsRestore 7 Backup and recoveryPage Restoring using the dedicated recovery partition select models only Performing a system restoreChanging the computer boot order Restoring using the restore mediaBacking up and recovering your information Using Windows system restore points Using Windows Backup and RestoreWhen to create restore points Restore to a previous date and time Create a system restore pointRequirements for all countries 8 Power cord set requirements98 Chapter 8 Power cord set requirements Requirements for specific countries and regions9 Recycling BatteryDisplay 3. Remove the display bezel Perform the following steps100 Chapter 9 Recycling 7. Turn the display panel assembly upside down 6. Remove the display panel assembly 2 from the display enclosureDisplay 12. Lift the top edge of the backlight cover 2 and swing it outward 10. Remove the display panel frame 2 from the display panel13. Remove the backlight cover 14. Turn the display panel right-side up17. Remove the backlight frame from the display panel 16. Turn the display panel upside down18. Remove the backlight from the backlight frame Display21. Release the LCD panel 3 from the display rear panel 19. Disconnect the display cable 1 from the LCD panel23. Remove the LCD panel 24. Recycle the LCD panel and backlight 104 Chapter 9 RecyclingIndex J jacks