3 • Setting Jumpers & DIP Switches
BEFORE INSTALLING THE CONTROL:
1.Use the pull chain switch to set the fan speed to the HIGH position before installation. Example Settings
Do not use the pull chain to change the fan speed after installation, as damage to ReceiverTransmitter
your ceiling fan or universal control may result. The speed of the fan should only be |
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
| |||||||||
changed by the Hunter control. |
|
|
|
|
|
|
|
|
| 4 | 3 2 1 |
|
| ||||||
2. Set the ceiling fan light kit to the ON position before installation. The light level should |
|
|
|
|
|
|
|
|
|
|
| ||||||||
only be changed by the Hunter control. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Installation Instructions: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| Jumpers |
| DIP Switches | |||||
1. Disconnect power to the ceiling fan and light kit at the main electrical panel. Remove fuse or move circuit breaker |
|
|
|
|
| ||||||||||||||
to the OFF position. |
|
|
|
|
|
|
|
|
|
|
| Set to 0111 |
| Set to 0111 | |||||
2. IMPORTANT! Change the position of the jumpers in the transmitter and the DIP switches in the receiver. | Figure 1 |
|
| ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
| |||||||||
Before you change a jumper, make sure the battery is not connected to the transmitter. Be sure the position of the |
|
|
|
|
|
|
|
|
|
|
| ||||||||
jumpers in the transmitter match the position of the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DIP switches on the receiver. If they don’t match, |
|
|
|
|
|
|
| Figure 3 |
|
|
|
|
|
|
|
| |||
the controller will not function. The DIP switches |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
for the receiver are located on the flat surface of | Transmitter |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
the receiver. In the transmitter you can access the | Jumnpers |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
jumpers from the battery compartment. The jumpers |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
are very small. You can move them most easily | 4 |
| 3 |
| 2 | 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
using a small pair of pliers or tweezers. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| Receiver DIP |
|
| ||||||||||
3. When two or more fans are located near each other, |
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
| Switches |
|
|
|
|
|
|
|
| ||||
you may want to have the receiver/transmitter |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
for each fan set to a different code, so that the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
operation of one fan does not affect the operation |
|
|
|
|
|
| Figure 2 |
|
|
|
|
|
|
|
|
|
|
|
|
of the other fans. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4