1.0 SAFETY AND OPERATION RULES

Safety precautions are essential when any mechanical equipment is involved. These precautions are necessary when using, storing, and servicing mechanical equipment. Using this equipment with the respect and caution demanded will considerably lessen the possibilities of personal injury. If safety precautions are overlooked or ignored, personal injury or property damage may occur.

The following symbols shown below are used extensively throughout this manual. Always heed these precautions, as they are essential when using any mechanical equipment.

This warning symbol identifies specific instructions or procedures which if not correctly followed could result in perso-

WARNING nal injury or death.

This caution symbol identifies specific instructions or procedures which, if not strictly observed, could result in damage

CAUTION to, or destruction of equipment.

This unit was designed for specific applications. It should not be modified and/or used for any application other than that which it was designed.

When using this product basic precautions should always be followed, including the

WARNING following:.

1.Read this manual carefully - know your equipment. Consider the applications, limitations, and the potential hazards specific to your unit.

2.Outlets with a third prong ground are required. Do not use without grounded prong.

3.Do not touch plug or outlet with wet hands.

4.Avoid accidental starts. Move switch on unit to “OFF” position before connecting or disconnecting cord to electrical outlets.

5.Water spray must never be directed towards any electric wiring or directly towards the pressure washer machine itself or fatal electric shock may occur.

6.Never carry your pressure washer by the cord. Do not pull on the cord to disconnect from the outlet.

7.To prevent damage, the cord should not be crushed, placed next to sharp objects or near a heat source.

1.0 CONSIGNES D‘UTILISATION ET DE SÉCURITÉ

Il est essentiel de prendre des mesures de sécurité lors de l’utilisation de tout appareil mécanique. De telles mesures sont nécessaires pendant l’utilisation, le remisage et l’entretien de l’appareil mécanique. En utilisant l’appareil avec attention et dans le respect des consignes, les possibilités de blessures diminuent considérablement. Si ces mesures de sécurité sont ignorées ou ne sont pas mises en pratique, l’utilisateur risque de se blesser ou d’endommager l’appareil. Les symboles décrits ci-dessous sont largement utilisés dans le présent manuel. Tenez toujours compte des mesures de sécurité qui y sont associées, car elles sont essentielles lors de l’utilisation de tout appareil mécanique.

 

Ce symbole identifie des instructions ou

 

des procédures spécifiques qui, si elles

ATTENTION

ne sont pas appliquées, peuvent causer

de graves blessures ou entraîner la mort.

 

Ce symbole identifie des instructions ou

 

des procédures spécifiques qui, si elles

 

ne sont pas scrupuleusement observées,

IMPORTANT

peuvent endommager ou même détruire

 

l’appareil.

Cette unité a été conçue pour des applications spécifiques. Elle ne doit pas être modifiée ou utilisée pour des applications différentes de celle pour laquelle elle a été conçue.

Lors de l’utilisation de l’appareil, des précautions de base doivent être

ATTENTION observées, et notamment :

1.Lire attentivement le présent manuel pour une meilleure connaissance de l’appareil, au niveau de ses applications, ses limites et des risques potentiels.

2.Des prises de courant avec une troisième broche de terre sont nécessaires. Ne pas utiliser sans broche mise à la terre.

3.Ne pas toucher la prise avec les mains mouillées.

4.Éviter les démarrages accidentels. Mettre l’interrupteur en position ARRÊT, avant de brancher ou de débrancher le câble électrique à une prise.

5.Ne jamais diriger le jet d’eau sur des installations électriques ou sur le nettoyeur à pression afin d’éviter une décharge électrique mortelle.

6.Ne pas déplacer le nettoyeur à pression en tirant sur le câble. Ne pas tirer le câble pour débrancher l’appareil de la prise.

7.Afin d’éviter des dommages, le câble ne doit pas être écrasé ou placé près d’objets tranchants ou de sources de chaleur.

8

Page 8
Image 8
Husky 1750 PSL warranty Safety and Operation Rules, Consignes D‘UTILISATION ET DE Sécurité, ’appareil

1750 PSL specifications

The Husky 1750 PSL is a high-performance injection molding machine that caters to the needs of various industries, including automotive, consumer goods, and medical applications. Known for its reliability and superior precision, the Husky 1750 PSL is engineered to deliver consistent results, ensuring that manufacturers achieve their production targets efficiently.

One of the standout features of the Husky 1750 PSL is its robust clamping system. The machine utilizes a patented hydraulic design that provides exceptional clamping force, which is essential for maintaining part quality during the molding process. This ensures that the molded components have tight tolerances and are free from defects, critical for industries requiring high precision.

The injection unit of the Husky 1750 PSL is designed for high-speed performance, allowing for rapid cycle times without compromising on quality. This is made possible through advanced injection technologies that optimize melt flow and pressure. The machine can handle a variety of materials, from standard thermoplastics to specialized resins, making it versatile for different applications.

An important aspect of the Husky 1750 PSL is its user-friendly interface. The advanced control system features a touchscreen display that allows operators to monitor and adjust machine parameters easily. Real-time data analytics enable predictive maintenance, reducing downtime, and enhancing productivity. This is particularly beneficial in high-demand manufacturing environments where efficiency is key.

Energy efficiency is another significant characteristic of the Husky 1750 PSL. The machine is designed to minimize energy consumption while maximizing output. Its integrated design reduces the overall footprint of the system, making it suitable for facilities with space constraints. Additionally, the machine is optimized for low noise operation, contributing to a better working environment.

Durability and reliability are inherent to Husky’s design principles. The components used in the Husky 1750 PSL are built to withstand the rigors of continuous operation, ensuring a longer lifespan and lower maintenance costs. Companies investing in this machine benefit from reduced operating expenses over time.

In conclusion, the Husky 1750 PSL epitomizes innovation in the field of injection molding technology. With its combination of precision, efficiency, and user-friendly features, it provides manufacturers with the tools they need to succeed in a competitive landscape. This machine not only enhances production capabilities but also supports sustainability initiatives through its energy-efficient design.