Control Panel / Discharge Chute, Knob Black | Husqvarna 1130SB-LSB

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38

5

7
16
3	18	19
17	18
17
		6
	19
	6

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 42 17-14 CHUTE WELDMENT

2532 18 41-13 DEFLECTOR WELDMENT

3532 42 11-63 DEFLECTOR CONTROL ASSEMBLY

4532 42 03-25 DEFLECTOR SEAL

5	532 41 42-80	KNOB BLACK
6	532 12 84-15	POP RIVET

7817 50 10-10 SCREW 10−24 X .625

8532 41 98-21 CHUTE SNOW SHIELD

9532 42 17-28 SHIELD RETAINER STRAP

*10	532 17 98-29 SHOULDER BOLT 1/4−20 X .375
*11	532 17 92-46 PLASTIC WASHER
*12	532 19 17-30	NUT 1/4−20	6
*13	872 25 05-05	CARRIAGE BOLT 3/8−16 X .625
*14	532 75 11-53	NUT 5/16−18
*15	532 18 45-05	DEFLECTOR SPRING

16532 42 06-79 (SERVICE PART) DEFLECTOR CONTROL

17532 42 11-64 (SERVICE PART) DEFLECTOR CABLE GRAY

18532 42 11-38 DEFLECTOR SHIELD

19532 42 32-47 DEFLECTOR SHIELD STRAP

	*15		*12
			*12
			*11
	2		*10
	4	6	*10
		6

6	*14

1

*13

01.09.006-C

9 8

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 25

Image 25

Husqvarna 1130SB-LSB Control Panel / Discharge Chute, Knob Black, POP Rivet, 532 42 17-28 Shield Retainer Strap

Contents

1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Electric start button used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Auger Housing / Impeller Assembly Repair Parts KEY Part Description Auger Ball Bearing Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate 01.16.001-A Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer Strap Cable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot Bracket Handles POP Rivet 1/8 Pivot Support Lower Tube Gray 532 40 57-40 Traction ROD Assembly 532 18 04-80 Impeller ROD Assembly532 18 77-16 Shifter ROD Bottom Clutch ROD 532 42 14-48 Headlight Bezel Gray Grip Switch532 17 86-66 Halogen Headlight Bulb Drive Trunnion Bearing Assembly 532 19 84-74 Speed Selector Head Assembly532 19 77-63 Drive Plate Weldment HEX Shaft 532 18 00-82 Intermediate Gear AssemblyClevis PIN 532 17 53-44 Trunnion Bearing Roll PIN 3/16 Axle ShaftGear Clik PIN Wheel Lobe CoverClutch Slide Axle Lobe Frame Chassis / Engine / PulleysBottom PAN Engine Mount Plate Impeller Belt Pulley Wheels Power Cord Repair Parts532 19 30-71 Safety Ignition KEY Retainer PIN DECAL, Husq DECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement