Washer, POP Rivet 1/8 | Husqvarna 1130SB-LSB specs

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38

10

					1
			5	6
	10			6
	10
			8		7
			2
	5	8		3	9
	5			3

		6		7
		8
		4	9
		4
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 42 17-08 PLOW HANDLE LH

2532 42 17-09 PLOW HANDLE RH

3	532 19 69-44 PANEL BRACKET LH

4532 19 69-43 PANEL BRACKET RH

5532 41 45-15 HEATED HANDLE GRIP

	6	874 78 05-12 SCREW 5/16−18 X .750		01.08.011-A
	7	874 78 05-24	SCREW 5/16−18 X 1.50	01.08.011-A
	7	874 78 05-24	SCREW 5/16−18 X 1.50
	8	532 75 11-53	NUT 5/16−18
	9	532 15 54-15	WASHER
	10	532 17 87-75	POP RIVET 1/8

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

28

Image 28

Husqvarna 1130SB-LSB owner manual Washer, POP Rivet 1/8

Contents

1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Electric start button used for starting the engine HOW to USE Your Snow Thrower Stopping Using the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Repair Parts Auger Housing / Impeller Assembly KEY Part Description Auger Ball Bearing Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate 01.16.001-A Control Panel / Discharge Chute Knob BlackPOP Rivet 532 42 17-28 Shield Retainer Strap 532 42 11-60 LEVER/CABLE Rotator Assembly Gray Cable Assembly GrayRotator Head Rotator Pivot Bracket Handles POP Rivet 1/8 Lower Tube Gray Pivot Support 532 18 04-80 Impeller ROD Assembly 532 40 57-40 Traction ROD Assembly532 18 77-16 Shifter ROD Bottom Clutch ROD Grip Switch 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight Bulb Drive 532 19 84-74 Speed Selector Head Assembly Trunnion Bearing Assembly532 19 77-63 Drive Plate Weldment HEX Shaft Assembly 532 18 00-82 Intermediate GearClevis PIN 532 17 53-44 Trunnion Bearing Axle Shaft Roll PIN 3/16Gear Clik PIN Cover Wheel LobeClutch Slide Axle Lobe Chassis / Engine / Pulleys FrameBottom PAN Engine Mount Plate Pulley Impeller Belt Wheels Repair Parts Power Cord532 19 30-71 Safety Ignition KEY Retainer PIN DECAL, Husq DECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement