Lower Tube Gray, Pivot Support | Husqvarna 1130SB-LSB guide

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38

1

4

4

01.05.007-B

4

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 42 17-05	LOWER TUBE GRAY
2	532 42 21-17	PIVOT SUPPORT

3817 00 05-12 BOLT 5/16−18 X .750

4817 00 06-16 SCREW 3/8−16 X 1.00

2

3

4

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29

Image 29

Husqvarna 1130SB-LSB owner manual Lower Tube Gray, Pivot Support

Contents

1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Electric start button used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine If Recoil Starter has Frozen To Start EngineBefore Stopping General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Auger Housing / Impeller Assembly Repair Parts KEY Part Description Auger Ball Bearing Skid Plate Auger Assembly 30 LHAuger Assembly 30 RH 01.16.001-A Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer Strap Cable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot Bracket Handles POP Rivet 1/8 Pivot Support Lower Tube Gray 532 40 57-40 Traction ROD Assembly 532 18 04-80 Impeller ROD Assembly532 18 77-16 Shifter ROD Bottom Clutch ROD 532 42 14-48 Headlight Bezel Gray Grip Switch532 17 86-66 Halogen Headlight Bulb Drive Trunnion Bearing Assembly 532 19 84-74 Speed Selector Head Assembly532 19 77-63 Drive Plate Weldment HEX Shaft 532 18 00-82 Intermediate Gear AssemblyClevis PIN 532 17 53-44 Trunnion Bearing Roll PIN 3/16 Axle ShaftGear Clik PIN Wheel Lobe CoverClutch Slide Axle Lobe Frame Chassis / Engine / PulleysBottom PAN Engine Mount Plate Impeller Belt Pulley Wheels Power Cord Repair Parts532 19 30-71 Safety Ignition KEY Retainer PIN 532 18 37-30 DECAL, Remote Deflector DECAL, Husq 532 18 10-35 DECAL, DANGER, DeflectorDECAL, Husq Service Notes Service Notes Warranty Statement