Pulley, Impeller Belt | Husqvarna 1130SB-LSB specs

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 19 22-13 COVER ASSEMBLY
2	532 17 91-57	PULLEY
3	532 41 97-44 TRACTION BELT
4	532 40 80-07	IMPELLER BELT

401.04.003-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 38

Image 38

Husqvarna 1130SB-LSB owner manual Pulley, Impeller Belt

Contents

1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Electric start button used for starting the engine HOW to USE Your Snow Thrower Stopping To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Before Starting the Engine If Recoil Starter has Frozen To Start EngineBefore Stopping Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Repair Parts Auger Housing / Impeller Assembly KEY Part Description Auger Ball Bearing Skid Plate Auger Assembly 30 LHAuger Assembly 30 RH 01.16.001-A POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer Strap Rotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot Bracket Handles POP Rivet 1/8 Lower Tube Gray Pivot Support 532 18 77-16 Shifter ROD Bottom 532 18 04-80 Impeller ROD Assembly532 40 57-40 Traction ROD Assembly Clutch ROD 532 17 86-66 Halogen Headlight Grip Switch532 42 14-48 Headlight Bezel Gray Bulb Drive 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly HEX Shaft Clevis PIN Assembly532 18 00-82 Intermediate Gear 532 17 53-44 Trunnion Bearing Gear Axle ShaftRoll PIN 3/16 Clik PIN Clutch Slide CoverWheel Lobe Axle Lobe Bottom PAN Chassis / Engine / PulleysFrame Engine Mount Plate Pulley Impeller Belt Wheels 532 19 30-71 Safety Ignition KEY Repair PartsPower Cord Retainer PIN 532 18 37-30 DECAL, Remote Deflector DECAL, Husq 532 18 10-35 DECAL, DANGER, DeflectorDECAL, Husq Service Notes Service Notes Warranty Statement

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38

KEY

PULLEY

IMPELLER BELT