Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 18 ProFlex, 20 ProFlex manual Driving, Before starting, Starting the engine

Models: 18 ProFlex, 20 ProFlex

1 48

Download 48 pages 51.33 Kb

Page 15

Image 15

DRIVING

Before starting

•Read the safety instructions and information on the location and function of the controls before starting (see pages 5–12).

•Conduct daily maintenance before starting (see maintenance schedule on page 17).

•Adjust the seat to the required position.

Starting the engine

1.Lift up the cutting unit by pulling the lever back- wards to locked position (transport position) and apply the parking brake.

2. Move the throttle control to the middle position.

3.If the engine is cold move the choke lever backwards to its end position.

4. Turn the ignition key to the start position.

English – 13

Page 15

Image 15

Husqvarna 18 ProFlex, 20 ProFlex manual Driving, Before starting, Starting the engine

Contents

101 89 Rider 18 ProFlex Rider 20 ProFlexOperator´s manual Svenska Rider 18 ProFlex and Rider 20 ProFlex CONTENTS Operator’s Manual forII.Slope operation SAFETY INSTRUCTIONSSafe operation practices for ride-onmowers I.General operationSAFETY INSTRUCTIONS IV. ServiceEXPLANATION OF SYMBOLS Never carry passengers General useRead the instructions before starting the machine Clear the area from stones etc. before cuttingSAFETY INSTRUCTIONS Be extra careful when driving on slopesDriving on slopes Cut slopes upwards and downwards, not sidewaysNever allow children to drive the machine MaintenanceChildren Keep children away from the mowing areaNever drive the machine in an enclosed space SAFETY INSTRUCTIONSBe careful with the maintenance of the battery PRESENTATION Presentation9 10 1112 13 Location of the controls PRESENTATION Throttle controlChoke lever Speed limiterLowering of the cutting unit Cutting unitLift lever for cutting unit Lifting of the cutting unitFuelling Lever for adjustment of the cutting heightParking brake SeatDRIVING Before startingStarting the engine DRIVING Driving the machineDRIVING Cutting tips16 - English Stopping the engineDisengage lever DRIVINGMaintenance schedule MAINTENANCENose Dismantling of the machine hoodsMAINTENANCE Engine hoodFULL Check the engine’s oil levelCheck the engine’s cooling air intake Checking of the fuel pump’s air filter20 - English Check the transmission’s air intakeCheck the transmission’s oil level MAINTENANCEMAINTENANCE Checking and adjustment of the steering wiresMAINTENANCE Adjusting the brakesCheck the level of the battery acid Check the safety systemIMPORTANT INFORMATION Replacing the air filterMAINTENANCE Do not use compressed air to clean theThe parts of the cutting unit Fitting the cutting unitMAINTENANCE MAINTENANCE Belt diagram5 mm ParallelismCutting height MAINTENANCEMAINTENANCE Checking the blades Service position for the cutting unitPlacing in the service position Releasing from the service position5.Remove the belt adjuster’s spring Dismantling the cutting unitMAINTENANCE 3.Lift up the unit using the lifting lever14.Lift the unit off of the Rider MAINTENANCEMAINTENANCE Dismantling the beltMAINTENANCE Assembling the beltReplacing the cutting unit’s belts MAINTENANCEBelt replacement on the BioClip unit 10 N MAINTENANCEIMPORTANT INFORMATION 7 mmChanging the oil MAINTENANCEFULL MAINTENANCE Replacement of the oil filterLubrication General lubricationMAINTENANCE Checking and adjustment of the throttle wireMAINTENANCE Replacement of the fuel filterCleaning the pulse air filter Checking the tyre pressureTROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage 4.Ignition lock 5.Counter 6.Start relay 7.Engine WIRING DIAGRAM1.Brake switch, hydrostat 2.Microswitch, cutting unit 3.Microswitch, seatRider ProFlex TECHNICAL DATABioClip TECHNICAL DATACutting unit Rear ejector«*2¤J6¬ NOTES44 - English English «*2¤J6¬ 1998W51