Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 18 ProFlex, 20 ProFlex manual Check the transmission’s air intake, Maintenance, English

Models: 18 ProFlex, 20 ProFlex

1 48

Download 48 pages 51.33 Kb

Page 22

Image 22

MAINTENANCE

Check the transmission’s air intake

Check that the transmission’s air intake in not blocked.

Check the transmission’s oil level

1.Check the transmission’s oil level by looking through the mesh on the air intake. The oil level

should lie between the MIN and MAX markings on the oil canister at 20° C.

If oil needs to be added the transmission cover must be dismantled first. Release the two screws (one on each side) and then lift off the transmission cover.

2.Screw off the oil canister cap and top up with engine oil SAE 10W/30, class CD–CF, until the

oil level reaches the MAX marking. Screw the oil canister cap back on, and fit the transmission cover.

20 – English

Page 22

Image 22

Husqvarna 18 ProFlex, 20 ProFlex Check the transmission’s air intake, Check the transmission’s oil level, Maintenance

Contents

Rider 18 ProFlex Rider 20 ProFlex 101 89Operator´s manual Svenska CONTENTS Operator’s Manual for Rider 18 ProFlex and Rider 20 ProFlexI.General operation SAFETY INSTRUCTIONSSafe operation practices for ride-onmowers II.Slope operationIV. Service SAFETY INSTRUCTIONSEXPLANATION OF SYMBOLS Clear the area from stones etc. before cutting General useRead the instructions before starting the machine Never carry passengersCut slopes upwards and downwards, not sideways Be extra careful when driving on slopesDriving on slopes SAFETY INSTRUCTIONSKeep children away from the mowing area MaintenanceChildren Never allow children to drive the machineSAFETY INSTRUCTIONS Never drive the machine in an enclosed spaceBe careful with the maintenance of the battery Presentation PRESENTATION9 10 1112 13 Location of the controls Speed limiter Throttle controlChoke lever PRESENTATIONLifting of the cutting unit Cutting unitLift lever for cutting unit Lowering of the cutting unitSeat Lever for adjustment of the cutting heightParking brake FuellingBefore starting DRIVINGStarting the engine Driving the machine DRIVINGCutting tips DRIVINGDRIVING Stopping the engineDisengage lever 16 - EnglishMAINTENANCE Maintenance scheduleEngine hood Dismantling of the machine hoodsMAINTENANCE NoseChecking of the fuel pump’s air filter Check the engine’s oil levelCheck the engine’s cooling air intake FULLMAINTENANCE Check the transmission’s air intakeCheck the transmission’s oil level 20 - EnglishChecking and adjustment of the steering wires MAINTENANCECheck the safety system Adjusting the brakesCheck the level of the battery acid MAINTENANCEDo not use compressed air to clean the Replacing the air filterMAINTENANCE IMPORTANT INFORMATIONFitting the cutting unit The parts of the cutting unitMAINTENANCE Belt diagram MAINTENANCEMAINTENANCE ParallelismCutting height 5 mmMAINTENANCE Releasing from the service position Service position for the cutting unitPlacing in the service position Checking the blades3.Lift up the unit using the lifting lever Dismantling the cutting unitMAINTENANCE 5.Remove the belt adjuster’s springMAINTENANCE 14.Lift the unit off of the RiderDismantling the belt MAINTENANCEAssembling the belt MAINTENANCEMAINTENANCE Replacing the cutting unit’s beltsBelt replacement on the BioClip unit 7 mm MAINTENANCEIMPORTANT INFORMATION 10 NMAINTENANCE Changing the oilFULL General lubrication Replacement of the oil filterLubrication MAINTENANCEChecking and adjustment of the throttle wire MAINTENANCEChecking the tyre pressure Replacement of the fuel filterCleaning the pulse air filter MAINTENANCEProblem TROUBLE SHOOTING SCHEDULEProcedure STORAGE ServiceWinter storage 2.Microswitch, cutting unit 3.Microswitch, seat WIRING DIAGRAM1.Brake switch, hydrostat 4.Ignition lock 5.Counter 6.Start relay 7.EngineTECHNICAL DATA Rider ProFlexRear ejector TECHNICAL DATACutting unit BioClipNOTES «*2¤J6¬44 - English English 1998W51 «*2¤J6¬