Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 18 ProFlex, 20 ProFlex manual Dismantling the belt, Maintenance

Models: 18 ProFlex, 20 ProFlex

1 48

Download 48 pages 51.33 Kb

Page 33

Image 33

MAINTENANCE

Dismantling the belt

Starting point when dismantling the belt:

•No unit attached to the Rider.

•The front of the belt is hung around the hook guard’s handle.

How the front of the belt is removed from the front belt pulley is evident from sections 5–8, on page 27.

The entire belt is only dismantled as set out below, when the snow plough is fitted on the Rider.

1.Dismantle the steering plate under the support wheel. Use two 13 mm socket spanners.

2.Unhook the spring on the blade brake.

3.Pry off the belt from the intermediate pulley and remove the belt.

English – 31

Page 33

Image 33

Husqvarna 18 ProFlex, 20 ProFlex manual Dismantling the belt, Maintenance

Contents

101 89 Rider 18 ProFlex Rider 20 ProFlexOperator´s manual Svenska Rider 18 ProFlex and Rider 20 ProFlex CONTENTS Operator’s Manual forSafe operation practices for ride-onmowers SAFETY INSTRUCTIONSI.General operation II.Slope operationSAFETY INSTRUCTIONS IV. ServiceEXPLANATION OF SYMBOLS Read the instructions before starting the machine General useClear the area from stones etc. before cutting Never carry passengersDriving on slopes Be extra careful when driving on slopesCut slopes upwards and downwards, not sideways SAFETY INSTRUCTIONSChildren MaintenanceKeep children away from the mowing area Never allow children to drive the machineNever drive the machine in an enclosed space SAFETY INSTRUCTIONSBe careful with the maintenance of the battery PRESENTATION Presentation9 10 1112 13 Location of the controls Choke lever Throttle controlSpeed limiter PRESENTATIONLift lever for cutting unit Cutting unitLifting of the cutting unit Lowering of the cutting unitParking brake Lever for adjustment of the cutting heightSeat FuellingDRIVING Before startingStarting the engine DRIVING Driving the machineDRIVING Cutting tipsDisengage lever Stopping the engineDRIVING 16 - EnglishMaintenance schedule MAINTENANCEMAINTENANCE Dismantling of the machine hoodsEngine hood NoseCheck the engine’s cooling air intake Check the engine’s oil levelChecking of the fuel pump’s air filter FULLCheck the transmission’s oil level Check the transmission’s air intakeMAINTENANCE 20 - EnglishMAINTENANCE Checking and adjustment of the steering wiresCheck the level of the battery acid Adjusting the brakesCheck the safety system MAINTENANCEMAINTENANCE Replacing the air filterDo not use compressed air to clean the IMPORTANT INFORMATIONThe parts of the cutting unit Fitting the cutting unitMAINTENANCE MAINTENANCE Belt diagramCutting height ParallelismMAINTENANCE 5 mmMAINTENANCE Placing in the service position Service position for the cutting unitReleasing from the service position Checking the bladesMAINTENANCE Dismantling the cutting unit3.Lift up the unit using the lifting lever 5.Remove the belt adjuster’s spring14.Lift the unit off of the Rider MAINTENANCEMAINTENANCE Dismantling the beltMAINTENANCE Assembling the beltReplacing the cutting unit’s belts MAINTENANCEBelt replacement on the BioClip unit IMPORTANT INFORMATION MAINTENANCE7 mm 10 NChanging the oil MAINTENANCEFULL Lubrication Replacement of the oil filterGeneral lubrication MAINTENANCEMAINTENANCE Checking and adjustment of the throttle wireCleaning the pulse air filter Replacement of the fuel filterChecking the tyre pressure MAINTENANCETROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage 1.Brake switch, hydrostat WIRING DIAGRAM2.Microswitch, cutting unit 3.Microswitch, seat 4.Ignition lock 5.Counter 6.Start relay 7.EngineRider ProFlex TECHNICAL DATACutting unit TECHNICAL DATARear ejector BioClip«*2¤J6¬ NOTES44 - English English «*2¤J6¬ 1998W51