Manuals / Husqvarna / Lawn and Garden / Chainsaw

Husqvarna 395XPG, 1153177-95 Saw chain ﬁling and ﬁle gauges, 050/1,3 mm, 058/1,5 mm, 063/1,6 mm

Models: 395XPG 1153177-95

1 44

Download 44 pages 17.6 Kb

Page 40

TECHNICAL DATA

Recommended original and replacement bar and chain combinations

The Husqvarna 395XP is in the ANSI category of saws above 3,8 cu. in. and is not required to comply with low kickback performance requirements. However, for this model we recommend the following cutting equipment.

		Bar			Chain

Length, inch	Pitch, inch	Gauge, inch	Max. nose radius	Type		Drive link count

18	3/8		11T			68

20	3/8	0,058	11T	Husqvarna H42,		72
24	3/8	0,058	11T	Husqvarna H48		84
24	3/8		11T	Husqvarna H48		84

28	3/8		11T			93

Note: For the chains above you are free to choose between 0,050", 0,058" and 0,063" gauge drive link for the corresponding bar, see the table below.

0,050"/1,3 mm	H46	H47

0,058"/1,5 mm	H42	H48

0,063"/1,6 mm	H45	H50

WARNING! This chain saw model is capable of severe kickback that could result in serious injuries

! to the user. Do not operate this saw unless you have extraordinary cutting needs and experience and specialized training for dealing with kickback. Saws with signiﬁcantly reduced kickback potential are available. Always use the safest saw and cutting equipment applicable to your cutting need.

Saw chain ﬁling and ﬁle gauges

40 – English

Image 40

Husqvarna 395XPG, 1153177-95 manual Saw chain ﬁling and ﬁle gauges, 050/1,3 mm, 058/1,5 mm, 063/1,6 mm

Contents

395XP 395XPG Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Stop switch Cutting equipmentVibration damping system MufﬂerBar Cutting equipment designed to reduce kickbackChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethIncreased if the depth gauge setting is Adjustment of depth gauge settingTensioning the chain Too largeLubricating cutting equipment Filling with chain oilChecking chain lubrication Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentFitting the bar and chain AssemblyWorking with the chain Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutWhat is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentFine adjustment of the idling speed T Correctly adjusted carburetorHigh speed jet H Checking brake band wearChecking the inertia brake release ImmediatelyMufﬂer Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir ﬁlter Spark plugLubricating the bar tip sprocket Fitting the starterAdjustment of the oil pump Air Injection centrifugal cleaningWhen making adjustments Needle bearing lubricationWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain ﬁling and ﬁle gauges 050/1,3 mm058/1,5 mm 063/1,6 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Controlwarranty Parts List American Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsOriginal instructions 1153177-95