KEY Part Description, Scraper BAR | Husqvarna 96193005500 instruction

REPAIR PARTS SNOW THROWER - MODEL NUMBER 924SB (96193005500)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 40 78-80 AUGER HOUSING
2	532 41 62-15	SCRAPER BAR
3	872 27 05-05	CARRIAGE BOLT 5/16−18 X .625
4	532 15 53-77	NUT 5/16−18

3 (5x) 4 (5x)

01.07.001-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 43 57-94	AUGER ASSEMBLY LH 24
2	532 43 57-95	AUGER ASSEMBLY RH 24

01.07.017-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 21

Image 21

Husqvarna 96193005500 owner manual KEY Part Description, Scraper BAR, Auger Assembly LH, Auger Assembly RH

Contents

924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting Auger Assembly RH Auger Assembly LHKEY Part Description Scraper BAR Exploded Bearing ImpellerTool Clip Plug Skid Plate Deflector Seal Service Part Deflector Cable GrayKnob Black POP Rivet Cable Assembly Adjustable Gray 532 42 82-74 LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Gray Rotator Pivot Bracket Handle Grip Repair Parts Snow Thrower Model Number 924SB HandlesWasher Lower Tube Gray SHOULDERSCREW10-24X.625 532 42 14-48 Headlight Bezel GrayBulb Retainer Repair Parts Snow Thrower Model Number Spacer Repair Parts Snow Thrower Model Number 924SBKnob RED Handle Knob Axle Shaft Repair Parts Snow Thrower Model Number 924SB DriveRoll PIN 3/16 Gear Control Shaft Assembly 532 17 53-44 Trunnion Bearing AssemblyFlange Bearing HEX Shaft KEY Part 532 43 60-70 Complete LCT Engine 532 42 86-84 Cover AssemblyFrame KEY Part Description 532 42 92-69 Engine Mounting Plate Idler Pulley Wheels Repair Parts532 43 58-27 Steer Cable Bracket LH Steer Cable Bracket RH Cover 532 40Wheel Lobe Axle Lobe Power Cord Repair Parts Snow Thrower Model Number 924SB BAG of PartsKEY Part Description 532 42 26-63 Safety Ignition KEY Retainer PIN Repair Parts Snow Thrower Model Number 924SB Decals 532 18 10-35 DECAL, DANGER, Deflector532 42 95-69 DECAL, TRACT/CLUTCH Lever Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP

Husqvarna 96193005500 KEY Part Description, Scraper BAR, Auger Assembly LH, Auger Assembly RH

Models: 96193005500

KEY

PART

DESCRIPTION

SCRAPER BAR

AUGER ASSEMBLY LH 24

AUGER ASSEMBLY RH 24