To Remove Wheels See Fig, Carburetor | Husqvarna 96193005500

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 23)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN (INSTALL	OUTER HOLE
IN OUTER HOLE
OF AXLE ONLY)

AXLE

WHEEL

WHEEL HUB

Fig. 23

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 24)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

Fig. 24

18

Image 18

Husqvarna 96193005500 owner manual To Remove Wheels See Fig, Carburetor, Engine Speed, To Adjust Cable Tension See Fig

Contents

924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine To USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting KEY Part Description Auger Assembly LHAuger Assembly RH Scraper BAR Exploded Tool Clip ImpellerBearing Plug Skid Plate Knob Black Service Part Deflector Cable GrayDeflector Seal POP Rivet Cable Assembly Heat Shield Gray 532 42 82-74 LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Gray Rotator Pivot Bracket Washer Repair Parts Snow Thrower Model Number 924SB HandlesHandle Grip Lower Tube Gray Bulb 532 42 14-48 Headlight Bezel GraySHOULDERSCREW10-24X.625 Retainer Repair Parts Snow Thrower Model Number Knob RED Repair Parts Snow Thrower Model Number 924SBSpacer Handle Knob Roll PIN 3/16 Repair Parts Snow Thrower Model Number 924SB DriveAxle Shaft Gear Flange Bearing 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly HEX Shaft KEY Part Frame 532 42 86-84 Cover Assembly532 43 60-70 Complete LCT Engine KEY Part Description 532 42 92-69 Engine Mounting Plate Idler Pulley 532 43 58-27 Steer Cable Bracket LH Repair PartsWheels Steer Cable Bracket RH Wheel Lobe 532 40Cover Axle Lobe KEY Part Description 532 42 26-63 Safety Ignition KEY Repair Parts Snow Thrower Model Number 924SB BAG of PartsPower Cord Retainer PIN Repair Parts Snow Thrower Model Number 924SB Decals 532 18 10-35 DECAL, DANGER, Deflector532 42 95-69 DECAL, TRACT/CLUTCH Lever Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP