Axle Shaft, Roll PIN 3/16, Gear, Clik PIN

REPAIR PARTS SNOW THROWER - MODEL NUMBER 924SB (96193005500)

DRIVE

	7
1b	4
8	3
	3
1b
7	1a
	1a

01.03.001-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 40 49-23 (assy of 1a,1b) AXLE ASSEMBLY
1a	532 40 43-07	AXLE SHAFT
1b	532 18 42-06	ROLL PIN 3/16
2	532 18 00-81	GEAR

3532 17 46-97 THRUST WASHER

4532 17 98-30 AXLE BEARING

5532 14 63-15 SCREW 5/16−18 X .625

6817 49 05-08 BOLT 5/16−18 X .500

7	532 15 54-43	CLIK PIN
8	532 18 92-82	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 31

Image 31

Husqvarna 96193005500 Repair Parts Snow Thrower Model Number 924SB Drive, Axle Shaft, Roll PIN 3/16, Gear, Clik PIN

Contents

924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting Scraper BAR Auger Assembly LHAuger Assembly RH KEY Part Description Exploded Plug ImpellerBearing Tool Clip Skid Plate POP Rivet Service Part Deflector Cable GrayDeflector Seal Knob Black Rotator Pivot Bracket 532 42 82-74 LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Gray Cable Assembly Heat Shield Gray Lower Tube Gray Repair Parts Snow Thrower Model Number 924SB HandlesHandle Grip Washer Retainer 532 42 14-48 Headlight Bezel GraySHOULDERSCREW10-24X.625 Bulb Repair Parts Snow Thrower Model Number Handle Knob Repair Parts Snow Thrower Model Number 924SBSpacer Knob RED Gear Repair Parts Snow Thrower Model Number 924SB DriveAxle Shaft Roll PIN 3/16 HEX Shaft 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly Flange Bearing KEY Part KEY Part Description 532 42 92-69 Engine Mounting Plate 532 42 86-84 Cover Assembly532 43 60-70 Complete LCT Engine Frame Idler Pulley Steer Cable Bracket RH Repair PartsWheels 532 43 58-27 Steer Cable Bracket LH Axle Lobe 532 40Cover Wheel Lobe Retainer PIN Repair Parts Snow Thrower Model Number 924SB BAG of PartsPower Cord KEY Part Description 532 42 26-63 Safety Ignition KEY 532 18 10-35 DECAL, DANGER, Deflector Repair Parts Snow Thrower Model Number 924SB Decals532 42 95-69 DECAL, TRACT/CLUTCH Lever Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP

Husqvarna 96193005500 Repair Parts Snow Thrower Model Number 924SB Drive, Axle Shaft, Gear

Models: 96193005500

REPAIR PARTS SNOW THROWER - MODEL NUMBER 924SB (96193005500)

DRIVE

KEY

AXLE SHAFT

ROLL PIN 3/16

GEAR

CLIK PIN

SQUARE KEY