Meets A.N.S.I. Safety Requirements | Husqvarna 96193005500 guide

OPERATION

MUFFLER

GASOLINE

FILLER CAP

CHOKE

CON-

TROL

SAFETY

IGNITION

KEY

ON / OFF

SWITCH

PRIMER

FUEL SHUT-OFF VALVE

RECOIL (AUXILIARY) STARTER HANDLE

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

ELECTRIC AUGER

START CONTROL

BUTTON LEVER

POWER

CORD

PLUG

CHUTE

DEFLECTOR

DISCHARGE

CHUTE

CLEAN-OUT TOOL

Fig. 10

DISCHARGE CHUTE	DEFLECTOR REMOTE
CONTROL LEVER	CONTROL LEVER
DRIVE SPEED	TRACTION
CONTROL LEVER	DRIVE
	CONTROL
	LEVER

LH TURN

TRIGGER

LIGHT

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

ON / OFF switch - used to STOP the engine. Choke control - used for starting a cold engine.

LH and RH turn triggers - used to steer the snow thrower.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

9

Image 9

Husqvarna 96193005500 Meets A.N.S.I. Safety Requirements, Recoil auxiliary starter handle used for starting the engine

Contents

924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting Auger Assembly RH Auger Assembly LHKEY Part Description Scraper BAR Exploded Bearing ImpellerTool Clip Plug Skid Plate Deflector Seal Service Part Deflector Cable GrayKnob Black POP Rivet Cable Assembly Adjustable Gray 532 42 82-74 LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Gray Rotator Pivot Bracket Handle Grip Repair Parts Snow Thrower Model Number 924SB HandlesWasher Lower Tube Gray SHOULDERSCREW10-24X.625 532 42 14-48 Headlight Bezel GrayBulb Retainer Repair Parts Snow Thrower Model Number Spacer Repair Parts Snow Thrower Model Number 924SBKnob RED Handle Knob Axle Shaft Repair Parts Snow Thrower Model Number 924SB DriveRoll PIN 3/16 Gear Control Shaft Assembly 532 17 53-44 Trunnion Bearing AssemblyFlange Bearing HEX Shaft KEY Part 532 43 60-70 Complete LCT Engine 532 42 86-84 Cover AssemblyFrame KEY Part Description 532 42 92-69 Engine Mounting Plate Idler Pulley Wheels Repair Parts532 43 58-27 Steer Cable Bracket LH Steer Cable Bracket RH Cover 532 40Wheel Lobe Axle Lobe Power Cord Repair Parts Snow Thrower Model Number 924SB BAG of PartsKEY Part Description 532 42 26-63 Safety Ignition KEY Retainer PIN Repair Parts Snow Thrower Model Number 924SB Decals 532 18 10-35 DECAL, DANGER, Deflector532 42 95-69 DECAL, TRACT/CLUTCH Lever Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP