Parts Packed Separately in Carton | Husqvarna 96193005500 guide

PARTS PACKED SEPARATELY IN CARTON

	(1) POWER CORD	(1) MULTI-	(3) RETAINER
	(198563)
		WRENCH	SPRINGS

		(180684)	(169675)

	(2) SHEAR BOLTS 1/4-20 x 1-3/4	(2) LOCKNUTS
	(2) SHEAR BOLTS 1/4-20 x 1-3/4		1/4-20
	(192090)		1/4-20
	(192090)		(73800400)
			(73800400)
(2) FLAT WASHERS
	SAFTEY
	IGNITION KEY (S)
	(422663)
(2) CARRIAGE BOLTS	(1) LOCKNUT		(1) CARRIAGE BOLT
3/8-16 x 2.25	5/16-18		5/16-18 x 5/8
	(751153)		(72250505)

		(1) WASHER 3/8	(1) LOCKNUT 3/8	(1) LOCKNUT	(1) SHOULDER
	(2) HANDLE KNOBS			1/4-20	BOLT 1/4-20	(1) SPRING
		(19131316)	(73800600)	(191730)	(179829)	(184505)

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for ship- ping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

4

Image 4

Husqvarna 96193005500 Parts Packed Separately in Carton, Assembly / PRE-OPERATION, Remove Snow Thrower from Carton

Contents

924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig Using the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting Auger Assembly LH Auger Assembly RHKEY Part Description Scraper BAR Exploded Impeller BearingTool Clip Plug Skid Plate Service Part Deflector Cable Gray Deflector SealKnob Black POP Rivet 532 42 82-74 LEVER/CABLE Rotator Assembly Cable Assembly Adjustable GrayCable Assembly Heat Shield Gray Rotator Pivot Bracket Repair Parts Snow Thrower Model Number 924SB Handles Handle GripWasher Lower Tube Gray 532 42 14-48 Headlight Bezel Gray SHOULDERSCREW10-24X.625Bulb Retainer Repair Parts Snow Thrower Model Number Repair Parts Snow Thrower Model Number 924SB SpacerKnob RED Handle Knob Repair Parts Snow Thrower Model Number 924SB Drive Axle ShaftRoll PIN 3/16 Gear 532 17 53-44 Trunnion Bearing Assembly Control Shaft AssemblyFlange Bearing HEX Shaft KEY Part 532 42 86-84 Cover Assembly 532 43 60-70 Complete LCT EngineFrame KEY Part Description 532 42 92-69 Engine Mounting Plate Idler Pulley Repair Parts Wheels532 43 58-27 Steer Cable Bracket LH Steer Cable Bracket RH 532 40 CoverWheel Lobe Axle Lobe Repair Parts Snow Thrower Model Number 924SB BAG of Parts Power CordKEY Part Description 532 42 26-63 Safety Ignition KEY Retainer PIN 532 18 10-35 DECAL, DANGER, Deflector Repair Parts Snow Thrower Model Number 924SB Decals532 42 95-69 DECAL, TRACT/CLUTCH Lever Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP