532 42 82-74 LEVER/CABLE Rotator Assembly

REPAIR PARTS SNOW THROWER - MODEL NUMBER 924SB (96193005500)

CONTROL PANEL / CHUTE

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 42 82-74 LEVER/CABLE ROTATOR ASSEMBLY

2817 50 10-10 SCREW 10-24 X .625

*3	532 42 06-78 ROTATOR HEAD
*4	532 42 28-23	ROTATOR PIVOT BRACKET
*5	532 42 06-75	PULLEY PIVOT
*6	532 42 82-75	CABLE ASSEMBLY ADJUSTABLE GRAY
*7	532 42 83-11	CABLE ASSEMBLY HEAT SHIELD GRAY

01.09.011-B *5

NOTES:

1.ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

101.15.008-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 42 12-31	STEER CABLE
2	874 04 10-24	SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 26

Image 26

Husqvarna 96193005500 532 42 82-74 LEVER/CABLE Rotator Assembly, Rotator Pivot Bracket, Pulley Pivot, Steer Cable

Contents

924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine To USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting KEY Part Description Auger Assembly LHAuger Assembly RH Scraper BAR Exploded Tool Clip ImpellerBearing Plug Skid Plate Knob Black Service Part Deflector Cable GrayDeflector Seal POP Rivet Cable Assembly Heat Shield Gray 532 42 82-74 LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Gray Rotator Pivot Bracket Washer Repair Parts Snow Thrower Model Number 924SB HandlesHandle Grip Lower Tube Gray Bulb 532 42 14-48 Headlight Bezel GraySHOULDERSCREW10-24X.625 Retainer Repair Parts Snow Thrower Model Number Knob RED Repair Parts Snow Thrower Model Number 924SBSpacer Handle Knob Roll PIN 3/16 Repair Parts Snow Thrower Model Number 924SB DriveAxle Shaft Gear Flange Bearing 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly HEX Shaft KEY Part Frame 532 42 86-84 Cover Assembly532 43 60-70 Complete LCT Engine KEY Part Description 532 42 92-69 Engine Mounting Plate Idler Pulley 532 43 58-27 Steer Cable Bracket LH Repair PartsWheels Steer Cable Bracket RH Wheel Lobe 532 40Cover Axle Lobe KEY Part Description 532 42 26-63 Safety Ignition KEY Repair Parts Snow Thrower Model Number 924SB BAG of PartsPower Cord Retainer PIN 532 42 95-69 DECAL, TRACT/CLUTCH Lever Repair Parts Snow Thrower Model Number 924SB Decals532 18 10-35 DECAL, DANGER, Deflector Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP

KEY

1532 42 82-74 LEVER/CABLE ROTATOR ASSEMBLY

ROTATOR PIVOT BRACKET

PULLEY PIVOT

CABLE ASSEMBLY ADJUSTABLE GRAY

CABLE ASSEMBLY HEAT SHIELD GRAY

KEY

STEER CABLE