1

1

“A”“A”

2

Eng (1) Bottom edge of mower

(2) Lift link adjustment nut

D(1) Unterkante des Mähwerks

(2)Hubstangen-Stellmutter

F(1) Fond du bord de la tondeuse

(2)Écrou de réglage du raccord de levage

Esp (1) Parte inferior de la esquina de la segadora

(2) Tuerca de ajuste del várillaje de levantamiento

I(1) Bordo inferiore del tagliaerba

(2)Dado di regolazione dell'articolazione di sollevamento

NL (1) Onderkant van de maaimachine

(2) Bijstelmoer

Eng SIDE-TO-SIDE ADJUSTMENT

Raise mower to highest position.

At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” should be the same or within 6mm (1/4") of each other.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

Recheck measurements after adjusting.

DSEITLICHE EINSTELLUNG

Das Mähwerk auf die höchste Position einstellen.

Auf beiden Seiten des Mähwerks in der Mitte den Abstand von der Unterkante des Mähwerks zum Boden messen. Der Abstand “A” sollte auf den beiden Seiten um höchstens 6 mm (1/4') voneinander abweichen.

Falls eine Einstellung notwendig sein sollte, die Einstellung nur auf einer Seite des Mähwerks vornehmen.

Um eine Seite des Mähwerks anzuheben, die Hubstangen-Stellmutter auf der jeweiligen Seite festziehen.

Um eine Seite des Mähwerks abzusenken, die Hubstangen -Stellmutter auf der jeweiligen Seite lösen.

HINWEIS: Drei volle Umdrehungen der Stellmutter verändern die Höhe des Mähwerks um etwa 3 mm (1/8").

Nach der Einstellung die Abstände erneut prüfen

FREGLAGE TRANSVERSAL

Relever le carter de coupe dans sa position la plus haute.

Calculer la distance au sol à partir des milieux des bords extérieurs gauche et droite du carter de coupe.

La distance A doit être la mêne des deux côtés à 6 mm près.

Si le réglage est nécessaire, ne régler qu'un seul des deux côtés pr rapport à l'autre.

Soulever ou baisser un côté de la tondeuse en ajustant l'écrou de réglage sur ce côte.

ATTENTION: Chaque trois tour de l'écrou de réglage changera a hauteur de la tondeuse environ 0,3 cm (1/8").

Revérifier la distance au sol après le réglage.

Esp ADJUSTE DE LADO A LADO

Levante la segadora a su posición más alta.

A media distancia de ambos lados de la segadora, mida la altura desde la parte inferior del extremo de la segadora al suelo. La distancia “A” debe ser la misma o dentro de 6mm (1/4") de la una a la otra.

Si el ajuste es necesario, haga el ajuste en un lado de la segadora solamente.

Levante un lado de la segadora por apretar la tuerca de ajuste del várillaje de levantamiento en ese lado.

Baje un lado de la segadora por desapretar la tuerca de ajuste del várillaje de levantamiento en ese lado.

NOTA: Cada tres vueltas completas de la tuerca de ajuste cambiará la altura de la segadora en aproximadamente (1/8").

Vuelva a revisar las medidas después del adjuste.

IREGOLAZIONE FIANCO A FIANCO

Alzare il tagliaerba nella posizione più alta.

Sui punti centrali di entrabi i lati del tagliaerba, misurare l'altezza dal bordo inferiore del tagliaerba al suolo. La distanza “A” deve essere la stessa o diversa non più di circa 6mm (1/4 di pollice).

Se necessario, fare la regolazione su un solo lato del tagliaerba.

Per alzare un lato del tagliaerba, stringere il dado di regolazione dell'articolazione di sollevamento su quel lato.

Per abbassare un lato del tagliaerba, allentare il dado di regolazione dell'articolazione di sollevamento su quel lato.

OSSERVARE: Tre giri completi del dado di regolazione cambiano l'altezza del tagliaerba di circa 3 mm (1/8 di pollice).

Dopo aver fatto la regolazione, ricontrollare le misurazioni.

NL LINKS/RECHTS BIJSTELLEN

• Zet de maaimachine in de hoogste stand.

• Meet vervolgens in het midden tussen beide zijkanten van de maaimachine de hoogte van de onderkant van de maaimachine tot de grond. Afstand “A” moet ofwel hetzelfde zijn, ofwel binnen 6 mm (1/4") van elkaar liggen.

• Indien bijstellen nodig is, mag dit slechts aan één kant van de maaimachine gebeuren.

• Draai de bijstelmoer vaster aan de kant van de maaimachine die u hoger wilt instellen.

• Draai de bijstelmoer looser aan de kant van de maaimachine die u lager wilt instellen.

 

LET OP: Drei slagen van de bijstelmoer veranderen de

77

hoogte ongeveer 3 mm (1/8").

• Controleer na het bijstellen de hoogte opnieuw.

 

Page 77
Image 77
Husqvarna CTH160II Seitliche Einstellung, Reglage Transversal, Regolazione Fianco a Fianco, NL LINKS/RECHTS Bijstellen

CTH160II specifications

The Husqvarna CTH160II is a standout model in the realm of garden tractors, specifically designed to offer efficiency, comfort, and advanced features for homeowners with varying landscape needs. This machine is engineered for durability and performance, making it an ideal choice for maintaining lawns, gardens, and more extensive outdoor spaces.

One of the key features of the CTH160II is its powerful engine. Equipped with a robust Briggs & Stratton engine, it ensures reliable starting and strong performance, even under demanding conditions. The engine delivers a significant amount of horsepower, providing the necessary power for tackling tough mowing and terrain challenges.

The cutting deck on the CTH160II is another notable characteristic. With a 42-inch reinforced cutting deck, it provides a wide cutting path, which enhances efficiency and reduces mowing time. The deck is designed for superior grass collection and is compatible with various cutting heights, allowing users to achieve the desired grass length easily. Additionally, the deck features an innovative washout port, making maintenance straightforward by simplifying the cleaning process after use.

The ergonomics of the CTH160II are worth mentioning as well. The tractor is equipped with a comfortable seat that can be adjusted to accommodate different user preferences, thereby enhancing the overall mowing experience. The steering wheel is also positioned for optimal control, ensuring that the operator can maneuver the tractor effortlessly.

The Husqvarna CTH160II incorporates advanced technologies that enhance usability. Its hydrostatic transmission provides seamless speed control, eliminating the need for shifting gears, which makes it more accessible for users of all skill levels. Furthermore, the tractor features a compact design, allowing it to navigate through tight spaces and around obstacles with ease.

For those looking for versatility, the CTH160II can be equipped with various accessories, including mulching kits, sweeper attachments, and snow removal tools. This adaptability makes it suitable for a range of tasks throughout the year, from mowing to snow clearing.

In summary, the Husqvarna CTH160II combines power, precision, and user-friendly features, making it an excellent choice for homeowners looking to maintain their gardens and lawns efficiently. With its durable construction, thoughtful design, and impressive technological advancements, the CTH160II stands out as an essential tool for outdoor maintenance. Whether for routine mowing or more extensive landscaping tasks, this garden tractor is built to deliver reliable performance season after season.