Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna EZ4824 CA/ 966659501, EZ4824/ 966612901, EZ24T/ 966659601 Controls, Control Locations

Models: EZ4824 CA/ 966659501 EZ24T/ 966659601 EZ4824/ 966612901

1 60

Page 17

CONTROLS

This operator’s manual describes the Husqvarna Zero Turn Rider. The rider is fitted with Briggs & Stratton four-stroke overhead valve engine.

Transmission from the engine is made via a belt-

driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and thereby the direction and speed.

Control Locations

7	2

	4	5	3	6	12	10	11
8

1.	Steering control levers	8.	Fuel tank cap
2.	Parking brake	9.	Fuel shut off valve
3.	Throttle control	10.	Deck lift
4.	Blade switch	11.	Seat adjustment lever
5.	Ignition switch	12.	Hour meter
6.	Choke control	13.	Tracking adjustment
7.	Fuses	14.	Bypass linkages

Page 17

Image 17

Husqvarna EZ4824 CA/ 966659501, EZ4824/ 966612901, EZ24T/ 966659601 warranty Controls, Control Locations

Contents

EZ4824 / 966612901 EZ4824 CA / 966659501 EZ24T Operator Manual2011 All rights reserved Orangeburg, SC. Printed in U.S.A CONTENTS Page Congratulations INTRODUCTIONGeneral Driving and Transport on Public RoadsINTRODUCTION Good ServiceManufacturing Number IMPORTANT INFORMATION SYMBOLS AND DECALSXxxx xxxxxx xxxxx xxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxxxx Read SYMBOLS AND DECALSGeneral Operation SAFETYSafety Instructions Operate machine only in daylight or good artificial light SAFETYWhen using the machine, approved Personal Safety Equipmentat hand when using the machine Slope OperationSAFETY ChildrenThe engine and the exhaust system become very hot during operation Safe Handling of GasolineThere is risk for burns if touched Allow engine and exhaust system to cool before refuelingSAFETY General MaintenanceUse protective glasses for maintenance work Use protective goggles SAFETYSpark Arrestor Transportin effective working order by the operator SAFETYControl Locations CONTROLS1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse Steering Control LeversCONTROLS Parking Brake Blade SwitchThrottle Control CONTROLSChoke Control Ignition SwitchFuses CONTROLSThe engine and the exhaust system, become very hot during operation Fuel TankRisk for burns if touched CONTROLSSeat Adjustment Lever Cutting Height AdjusterFuel Shut Off Valve Always raise the deck to the highest position for transportTracking Knob Hour MeterBypass Linkages CONTROLSTraining OPERATIONSteering To move forward and backwardOPERATION Before StartingStarting the Engine 6. Move the throttle to the middle position OPERATION7. If the engine is cold, the choke control should be pulled up Place controls in neutral positionIMPORTANT INFORMATION OPERATION8. Press in and turn the ignition key to the start position Jumper Cables Weak BatteryTo remove cables, reverse order OPERATIONOPERATION Make sure that no one is near mower when engaging blade switchRunning Do not drive up or down hills with Operating On Hillsslopes greater than 10 degrees. Do not drive across slopesOPERATION Mowing TipsIMPORTANT INFORMATION Stopping the EngineOPERATION Moving Machine by Hand Make no adjustments without the engine stoppedZT-2800 Bypass Linkages the ignition key removed the parking brake activatedMaintenance Schedule MAINTENANCEMaintenance interval MAINTENANCEBefore performing any service or adjustment checklist MaintenancePlace the Blade-switch in the disengaged position Turn the ignition switch to OFF position and remove the keyAlways wear eye protection when around batteries BatteryCleaning battery and terminals Replacing batteryTire Pressures Safety SystemMAINTENANCE Parking BrakeV-belts Deck Belt InstallationDeck Belt Removal MAINTENANCEPump Belt Replacing pump belt Belt installationBelt removal MAINTENANCECutting Blades Blade replacementDo not use lower grade hardware than specified MAINTENANCEMAINTENANCE Adjusting the Mower DeckLeveling deck Only use O.E.M. specified tires Removal and installation Adjust anti-scalp rollers with the mower on a flat level surfaceCaster Wheels HardwareUse protective glasses when cleaning and washing CleaningMAINTENANCE Clean regularlyGeneral LUBRICATIONFront Wheel Bearings Front Wheel MountDeck Spindle Deck Outer SpindleLUBRICATION Transaxle Transmission Fluid ChangeProblem TROUBLESHOOTINGMaintenance section CauseCause TROUBLESHOOTINGProblem Never use gasoline for cleaning. Use a degreaser and warm water ServiceSTORAGE Winter StorageSCHEMATICS Torque Specifications TECHNICAL DATAAccessories HEX HEAD CAP SCREWSEZ24T \ EZ4824EZ4824CA EngineFrame DimensionTECHNICAL DATA EZ4824USA requirements CONFORMITY CERTIFICATESDelivery Service SERVICE JOURNALAfter the first 5-8 hours 25-Hour ServiceSERVICE JOURNAL Action100-Hour Service 50-Hour ServiceAt Least Once Each Year 300-Hour ServicePage 2011-10-06 115 384627 RevC