Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna EZ4824 CA/ 966659501 warranty Hour Meter, Tracking Knob, Bypass Linkages, Controls

Models: EZ4824 CA/ 966659501 EZ24T/ 966659601 EZ4824/ 966612901

1 60

Download 60 pages 28.66 Kb

Page 23

Hour Meter

CONTROLS

Hour Meter

The hour meter displays the total operating time.

It will flash CHG OIL (Change Oil) at 50 hour intervals. The flash duration is one hour before and one hour after the interval. The CHG OIL icon will come on and shut off automatically. The hour meter cannot be manually reset.

Tracking Knob

If the mower is not tracking straight, check the tire air pressures. Recommended air pressure is 15 psi (103 kPa / 1 bar) for all tires. Tracking must be checked on a flat and level concrete or blacktop surface.

Rotating the tracking knob allows fine tuning adjustments so the machine tracks straight with the steering control levers in the full forward position.

Rotate the knob clockwise (as viewed from the operation position) to increase the speed on the left lever. Rotate counterclockwise to decrease speed.

Bypass Linkages

Transaxle bypass linkages must be engaged when pushing or pulling the mower. The release levers are located on each side of the rear of the unit below the rear engine plate. See Moving Machine By Hand in the Operation section.

8052-001

Hour meter

8058-020

Tracking knob

8058-147

Release lever

23

Image 23

Husqvarna EZ4824 CA/ 966659501, EZ4824/ 966612901, EZ24T/ 966659601 Hour Meter, Tracking Knob, Bypass Linkages, Controls

Contents

EZ4824 / 966612901 EZ4824 CA / 966659501 EZ24T Operator Manual2011 All rights reserved Orangeburg, SC. Printed in U.S.A CONTENTS Page Driving and Transport on Public Roads INTRODUCTIONCongratulations GeneralINTRODUCTION Good ServiceManufacturing Number IMPORTANT INFORMATION SYMBOLS AND DECALSXxxx xxxxxx xxxxx xxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxxxx Read SYMBOLS AND DECALSGeneral Operation SAFETYSafety Instructions Operate machine only in daylight or good artificial light SAFETYSlope Operation Personal Safety EquipmentWhen using the machine, approved at hand when using the machineSAFETY ChildrenAllow engine and exhaust system to cool before refueling Safe Handling of GasolineThe engine and the exhaust system become very hot during operation There is risk for burns if touchedSAFETY General MaintenanceUse protective glasses for maintenance work Use protective goggles SAFETYSAFETY TransportSpark Arrestor in effective working order by the operatorControl Locations CONTROLS1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse Steering Control LeversCONTROLS CONTROLS Blade SwitchParking Brake Throttle ControlCONTROLS Ignition SwitchChoke Control FusesCONTROLS Fuel TankThe engine and the exhaust system, become very hot during operation Risk for burns if touchedAlways raise the deck to the highest position for transport Cutting Height AdjusterSeat Adjustment Lever Fuel Shut Off ValveCONTROLS Hour MeterTracking Knob Bypass LinkagesTo move forward and backward OPERATIONTraining SteeringOPERATION Before StartingStarting the Engine Place controls in neutral position OPERATION6. Move the throttle to the middle position 7. If the engine is cold, the choke control should be pulled upIMPORTANT INFORMATION OPERATION8. Press in and turn the ignition key to the start position OPERATION Weak BatteryJumper Cables To remove cables, reverse orderOPERATION Make sure that no one is near mower when engaging blade switchRunning not drive across slopes Operating On HillsDo not drive up or down hills with slopes greater than 10 degrees. DoOPERATION Mowing TipsIMPORTANT INFORMATION Stopping the EngineOPERATION the ignition key removed the parking brake activated Make no adjustments without the engine stoppedMoving Machine by Hand ZT-2800 Bypass LinkagesMAINTENANCE MAINTENANCEMaintenance Schedule Maintenance intervalTurn the ignition switch to OFF position and remove the key MaintenanceBefore performing any service or adjustment checklist Place the Blade-switch in the disengaged positionReplacing battery BatteryAlways wear eye protection when around batteries Cleaning battery and terminalsParking Brake Safety SystemTire Pressures MAINTENANCEMAINTENANCE Deck Belt InstallationV-belts Deck Belt RemovalMAINTENANCE Belt installationPump Belt Replacing pump belt Belt removalMAINTENANCE Blade replacementCutting Blades Do not use lower grade hardware than specifiedMAINTENANCE Adjusting the Mower DeckLeveling deck Hardware Adjust anti-scalp rollers with the mower on a flat level surfaceOnly use O.E.M. specified tires Removal and installation Caster WheelsClean regularly CleaningUse protective glasses when cleaning and washing MAINTENANCEGeneral LUBRICATIONDeck Outer Spindle Front Wheel MountFront Wheel Bearings Deck SpindleLUBRICATION Transaxle Transmission Fluid ChangeCause TROUBLESHOOTINGProblem Maintenance sectionCause TROUBLESHOOTINGProblem Winter Storage ServiceNever use gasoline for cleaning. Use a degreaser and warm water STORAGESCHEMATICS HEX HEAD CAP SCREWS TECHNICAL DATATorque Specifications AccessoriesEngine EZ4824EZ24T \ EZ4824CAEZ4824 DimensionFrame TECHNICAL DATAUSA requirements CONFORMITY CERTIFICATESDelivery Service SERVICE JOURNALAction 25-Hour ServiceAfter the first 5-8 hours SERVICE JOURNAL100-Hour Service 50-Hour ServiceAt Least Once Each Year 300-Hour ServicePage 2011-10-06 115 384627 RevC