hussman IGHT-ESH/ESHS-0010 39

Rev. 0010

(2)F28T5/TL830

(2)F28T5/TL830

(2)F28T5/TL830

* Stat-T

1400W/~240V#125-01-0492 Cal-RodHE-00-43"

	Ballast
	#125-01-3212
	WH3-120-164
	Ballast
	#125-01-3212
	WH3-120-164
	Ballast
	#125-01-3212
	WH3-120-164
H2	L2
	L1
H1	P	L

Toggle-LIGHTS 0307-01-#125	#225* -01-3301 Snap-OnT-Stat 20N11T002-L250 ON:183°F/OFF:210°F	*T-Stat	Infite Control	H2
Toggle-LIGHTS 0307-01-#125		Stat-T*	Infite Control	H2 H1
		#125 - 01 - 0492	1400W/~240V
		Cal-RodHE-00-43"
		#125-01-0492	1400W/~240V	H1
		Cal-RodHE-00-43"

L2		andcalibrationinstructions.
L1	L	wiring
P		control
L2		forwater
L1	L	and3
P	L	2
		Seesheets

DrawingNo.:

W6000027

Sheet 1 of3

ProjectTitle:

IndividualWellsHotFoodSelf-ServiceCounters

ASH-S/ESH-S-RGSH-L/S-12',10WellsDrawingTitle:

						10	T-StatBulb	L
	5	T-StatBulb	L	L
						9	T-StatBulb	L
							T-StatBulb
	4		L	L	Hz
	4	T-StatBulb	L	L	-50/60
WELLFOODHOTAPW12x20(10)UNIT 1104-01-#175 ~208/240VAC1200/1600W	32		LL	LL	CircuitI 208/240VAC-3Ph	78	T-StatBulb	LL
							T-StatBulb
		T-StatBulb
							T-StatBulb
		T-StatBulb
						6	T-StatBulb	L
							T-StatBulb
	1	T-StatBulb	L	L

L

L
L	CircuitII ~208/240V-3Ph-60Hz
L

L

BorisKasrel	BK	04.14.2000	final
DrawnBy:	CheckedBy:	Date:	NextAssembly:
By:
Date:

Revisions:

No. Description:

CircuitI	LOADS,Amps	~208V ~240V	22.6 26.1	18.2 21.0	14.6 16.8
			L1	L2	L3

POWER	ToggleSwitch
WaterFill	ToggleSwitch
	A
	To#2Pin controllersocket seesht2
	on

B

s

#125-01-1001 Contactor1

TermBlock

L1

L2

L3

N

G

TimeDelay	seesht2
To

CircuitII	LOADS,Amps	~208V ~240V	L1 24.8 28.6	L2 27.6 31.9	L3 18.2 21.0	Note:casemustbegrounded
				L2 27.6 31.9	L3 18.2 21.0

s
#125-01-1001
Contactor2
TermBlock	L1	L2	L3	N	G

HussmannCorporation 13770RamonaAvenue Chino,CA.91710 (909)-590-4910 Lic.#:644406

®

39

Contents

Rev Single-DeckService Hot Food Case Single-DeckService Hot Food Case ESH Combo with pedestal option p/n IGHT-ESH/ESHS-0010 General Instructions Table of Contents THIS BOOKLET CONTAINS INFORMATION ON: ESH / ESHS: Hot Food Cases SHIPPING DAMAGE Cut & Plan Views ESHS ESH (-SS) COMBO CASES Plan View Installation cont LEVELING B.When wedges are involved in a lineup, set them first Do not use cam locks to pull cases together LEVELING/JOINING INSTRUCTIONS FINISHING TOUCHES (PERFORM AFTER PLUMBING AND ELECTRICAL) ACCESS PANELS INSTALLING SPLASHGUARD position splashguard up behind the front panel first CASE MUST BE GROUNDED IMPORTANT OPERATION TIPS: *Never place food directly into warmer.Always use an inset and pan *Always use water in case wells, as it provides even heat and humidity *Make sure all pans are in the well units no matter the configuration *Using thermometer, check product before loading in case (150° -160° ) AUTO-FILLOPERATION START-UP 1.Close drain valve 3.Turn all overhead heat to the "5" position SHUTDOWN User Information cont 1.Scrub thoroughly,cleaning all surfaces,with soap and hot water 2.Rinse with hot water, but do not flood 3.Apply the sanitizing solution according to the manufacturer’s directions 4.Rinse thoroughly Lift-upGlass IMPORTANT READ BEFORE RAISING FRONT GLASS : CLAMSHELL ASSEMBLY INSTALL GLASS PISTON REPLACEMENT 1.OPEN GLASS.Glass must remain open throughout procedure 2.Loosen Allen set Screw (1) 3.While holding onto piston,remove and save pin (2) 4.Slide piston out RECOMMENDED ADJUSTMENTS VERIFY THAT THE CASE(S) HAVE BEEN LEVELED PROPERLY.TIPS & TROUBLESHOOTING Before calling for service if something seems wrong, check the following: 1. INSPECT THE GAP BETWEEN THE GLASS PANELS A. If pinched at the top: CHECK OPENING ACTION OF GLASS PANELS and note the following: corners touch or overlap at any point Go to items 4 & 4. STRATEGIES FOR CORRECTING UNEVEN GAP AND OPENING OVERLAP PROBLEMS 5.STRATEGIES FOR CORRECTING GLASS BOUNCE AND OPENING OVERLAP PROBLEMS ADJUST HINGES FRONT – BACK 6.VERTICAL AND FRONT TO BACK ADJUSTMENT AND OPENING OVERLAP PROBLEMS •VERTICAL ADJUSTMENT •FRONT– BACK ADJUSTMENT ESH, ESHS Self Service ESH-SS, ESHS-SS ESH-Combo, ESHS-Combo Combination Electrical Schematics Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page c)Complete start-upprocedures should include : 4.Hot Griddles are functioning 1.Allow the case to preheat for one hour prior to loading 6.Do not display more food than will be sold within a 4 hour period 13.Turn the equipment off and allow to cool before cleaning Cleaner Allen Stainless Steel Polish Limited Warranty Hussmann Impact are warranted for a total of five (5) years based upon the above criteria DUE TO FAILURE FOR ANY REASON. HUSSMANN SHALL NOT BE LIABLE: •For payment of labor for any removal or installation of warranted parts; Service Record MODEL: SERIAL NUMBER: