hussman IGHT-ESH/ESHS-0010 42

IGHT-ESH/ESHS-0010

Circuit1	Loads,Amp 208V 240V 17.5L1 20.3 13.1L2 15.2 13.1L3 15.2		Circuit2	Loads,Amp 208V 240V 13.0L1 15.0	L2	9.5L3 10.7	caseNote:mustbegrounded	endeachofthecase	protecttoO-Ringfrom0
					12.4
				330-01-#225*	10.7	L250-20N11T002 ON:183°F		atinstalledbetohaveStats-T	hingespringgasoutertonext Overhead	InstallationOverhead
				330-01-#225*	Stat-TOn-Snap	L250-20N11T002 ON:183°F	210°FOFF:	atinstalledbetohaveStats-T	hingespringgasoutertonext Overhead	InstallationOverhead	038LT/5T12F
											038LT/5T12F
											F28T5/TL830
											F21T5/TL830
											V042~/W0022
	5	rosneS		L		L					laC-doREH-60-"07
	5	rosneS		L		L

	4	rosneS	L	L
		rosneS		L
IndividualHotFoodWell 1200/1600W/~208/240V(5)	21 3		LL	LLL	60Hz-3Ø-1:~2208/240V	24"x48"Griddle /~208/240V390W(2)
						2000W/~240V
						griddle, Cal - Rod HE - 19 - 46"
		rosneS
		rosneS
		rosneS

~115V/5Amp's		black	orange	black	Circuit
~115V/5Amp's	OptionalRight	S
~115V/5Amp's	OptionalLeft	L1	L2	L3	N	G

		tsallaB
		3HW-021-461
		Ballast
	Cap	WH3-120-164
	Cap
		Ballast
		WH3-120-164
			black
H1	P	L	-60Hz
H1 H2 H2	P L1 L2 L2 L1	L	Circuit2:~2208/240V-1Ø

		L
	7						white
	6						LIGHT #125-01-0311
P1	1 2 3 4 5		black	orange	black		LIGHT #125-01-0311
POWER	#125-01-0311	S				Contactor
		TermBlock	L1	L2	L3	N	G

DrawingNo.:	W6000030.dft		Sheet 1 of1
ASH,ESH/S,RGSH-L/S,RGSHS	ComboHotFoodSelf-ServiceCounters		10'Combo:5IndividualWells+ 4'Griddle
ProjectTitle:			DrawingTitle:
BorisKasrel	BK	01.24.2000	final
DrawnBy:	CheckedBy:	Date:	NextAssembly:
By:
	Date:

Revisions:	No. Description:
HussmannCorporation	13770RamonaAvenue Chino,CA.91710 (909)-590-4910 Lic.#:644406
®

42

Contents

Rev Single-DeckService Hot Food Case Single-DeckService Hot Food Case ESH Combo with pedestal option p/n IGHT-ESH/ESHS-0010 General Instructions Table of Contents THIS BOOKLET CONTAINS INFORMATION ON: ESH / ESHS: Hot Food Cases SHIPPING DAMAGE Cut & Plan Views ESHS ESH (-SS) COMBO CASES Plan View Installation cont LEVELING B.When wedges are involved in a lineup, set them first Do not use cam locks to pull cases together LEVELING/JOINING INSTRUCTIONS FINISHING TOUCHES (PERFORM AFTER PLUMBING AND ELECTRICAL) ACCESS PANELS INSTALLING SPLASHGUARD position splashguard up behind the front panel first CASE MUST BE GROUNDED IMPORTANT OPERATION TIPS: *Never place food directly into warmer.Always use an inset and pan *Always use water in case wells, as it provides even heat and humidity *Make sure all pans are in the well units no matter the configuration *Using thermometer, check product before loading in case (150° -160° ) AUTO-FILLOPERATION START-UP 1.Close drain valve 3.Turn all overhead heat to the "5" position SHUTDOWN User Information cont 1.Scrub thoroughly,cleaning all surfaces,with soap and hot water 2.Rinse with hot water, but do not flood 3.Apply the sanitizing solution according to the manufacturer’s directions 4.Rinse thoroughly Lift-upGlass IMPORTANT READ BEFORE RAISING FRONT GLASS : CLAMSHELL ASSEMBLY INSTALL GLASS PISTON REPLACEMENT 1.OPEN GLASS.Glass must remain open throughout procedure 2.Loosen Allen set Screw (1) 3.While holding onto piston,remove and save pin (2) 4.Slide piston out RECOMMENDED ADJUSTMENTS VERIFY THAT THE CASE(S) HAVE BEEN LEVELED PROPERLY.TIPS & TROUBLESHOOTING Before calling for service if something seems wrong, check the following: 1. INSPECT THE GAP BETWEEN THE GLASS PANELS A. If pinched at the top: CHECK OPENING ACTION OF GLASS PANELS and note the following: corners touch or overlap at any point Go to items 4 & 4. STRATEGIES FOR CORRECTING UNEVEN GAP AND OPENING OVERLAP PROBLEMS 5.STRATEGIES FOR CORRECTING GLASS BOUNCE AND OPENING OVERLAP PROBLEMS ADJUST HINGES FRONT – BACK 6.VERTICAL AND FRONT TO BACK ADJUSTMENT AND OPENING OVERLAP PROBLEMS •VERTICAL ADJUSTMENT •FRONT– BACK ADJUSTMENT ESH, ESHS Self Service ESH-SS, ESHS-SS ESH-Combo, ESHS-Combo Combination Electrical Schematics Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page c)Complete start-upprocedures should include : 4.Hot Griddles are functioning 1.Allow the case to preheat for one hour prior to loading 6.Do not display more food than will be sold within a 4 hour period 13.Turn the equipment off and allow to cool before cleaning Cleaner Allen Stainless Steel Polish Limited Warranty Hussmann Impact are warranted for a total of five (5) years based upon the above criteria DUE TO FAILURE FOR ANY REASON. HUSSMANN SHALL NOT BE LIABLE: •For payment of labor for any removal or installation of warranted parts; Service Record MODEL: SERIAL NUMBER: