Manuals / Brands / Kitchen Appliance / Food Processor / hussman / Kitchen Appliance / Food Processor

hussman IGHT-ESH/ESHS-0010 13.Turn the equipment off and allow to cool before cleaning, Cleaner, Allen Stainless Steel Polish

1 47

Download 47 pages, 1.44 Mb

Rev. 0010

13.Turn the equipment off and allow to cool before cleaning.

14.To remove “baked-on” splatter from Stainless Steel, the following may be used

Grade F Italian Pumice	Scour or rub with a damp cloth
Liquid Nusteel	Scour with a small amount of a dry
	cloth
	Paste NuSteel
Household Cleaners	Rub with a damp cloth
Coopers Stainless Steel	Cleaner

Allen Stainless Steel Polish

Contents

Rev Single-DeckService Hot Food Case Single-DeckService Hot Food Case ESH Combo with pedestal option p/n IGHT-ESH/ESHS-0010 General Instructions Table of Contents THIS BOOKLET CONTAINS INFORMATION ON: ESH / ESHS: Hot Food Cases SHIPPING DAMAGE Cut & Plan Views ESHS ESH (-SS) COMBO CASES Plan View Installation cont LEVELING B.When wedges are involved in a lineup, set them first Do not use cam locks to pull cases together LEVELING/JOINING INSTRUCTIONS FINISHING TOUCHES (PERFORM AFTER PLUMBING AND ELECTRICAL) ACCESS PANELS INSTALLING SPLASHGUARD position splashguard up behind the front panel first CASE MUST BE GROUNDED IMPORTANT OPERATION TIPS: *Never place food directly into warmer.Always use an inset and pan *Always use water in case wells, as it provides even heat and humidity *Make sure all pans are in the well units no matter the configuration *Using thermometer, check product before loading in case (150° -160° ) AUTO-FILLOPERATION START-UP 1.Close drain valve 3.Turn all overhead heat to the "5" position SHUTDOWN User Information cont 1.Scrub thoroughly,cleaning all surfaces,with soap and hot water 2.Rinse with hot water, but do not flood 3.Apply the sanitizing solution according to the manufacturer’s directions 4.Rinse thoroughly Lift-upGlass IMPORTANT READ BEFORE RAISING FRONT GLASS : CLAMSHELL ASSEMBLY INSTALL GLASS PISTON REPLACEMENT 1.OPEN GLASS.Glass must remain open throughout procedure 2.Loosen Allen set Screw (1) 3.While holding onto piston,remove and save pin (2) 4.Slide piston out RECOMMENDED ADJUSTMENTS VERIFY THAT THE CASE(S) HAVE BEEN LEVELED PROPERLY.TIPS & TROUBLESHOOTING Before calling for service if something seems wrong, check the following: 1. INSPECT THE GAP BETWEEN THE GLASS PANELS A. If pinched at the top: CHECK OPENING ACTION OF GLASS PANELS and note the following: corners touch or overlap at any point Go to items 4 & 4. STRATEGIES FOR CORRECTING UNEVEN GAP AND OPENING OVERLAP PROBLEMS 5.STRATEGIES FOR CORRECTING GLASS BOUNCE AND OPENING OVERLAP PROBLEMS ADJUST HINGES FRONT – BACK 6.VERTICAL AND FRONT TO BACK ADJUSTMENT AND OPENING OVERLAP PROBLEMS •VERTICAL ADJUSTMENT •FRONT– BACK ADJUSTMENT ESH, ESHS Self Service ESH-SS, ESHS-SS ESH-Combo, ESHS-Combo Combination Electrical Schematics Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page c)Complete start-upprocedures should include : 4.Hot Griddles are functioning 1.Allow the case to preheat for one hour prior to loading 6.Do not display more food than will be sold within a 4 hour period 13.Turn the equipment off and allow to cool before cleaning Cleaner Allen Stainless Steel Polish Limited Warranty Hussmann Impact are warranted for a total of five (5) years based upon the above criteria DUE TO FAILURE FOR ANY REASON. HUSSMANN SHALL NOT BE LIABLE: •For payment of labor for any removal or installation of warranted parts; Service Record MODEL: SERIAL NUMBER: