![Setting the](/images/new-backgrounds/111833/11183329x1.webp)
| The | adapter | has a | switch block that selects configuration options fo | |||||||||||||||||||||
| option | switches | are | preset | during | manufacture | to the | following | values. |
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
10 | (BW) |
| 9 (ED) | 8 (C8) |
| 7 | (C4) |
| 6 (C2) |
| 5 (C1) |
| 4 |
| 3 (L4) |
| 2 (L2) |
| 1 (L1) |
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| On |
|
|
| On | On |
|
| On |
|
| On |
|
| On |
| Off | Off |
| On |
| On |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| Switch | Number |
|
| Factory | Setting |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| 10 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
| 9 |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| 8+7+6+5 |
|
|
| Base |
| address: 02A0h |
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| 4 |
|
|
|
|
| Not used |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| 3+2+1 |
|
|
| IRQ | 10 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| |||||||||||||||||||
| If | your | installation | requires settings different than the preset values, perform eac | |||||||||||||||||||||
| Ÿ | “Setting | the | Bus | Width” |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| Ÿ | “Setting | the | ISA | Connector | Type” | on |
| page |
|
|
|
|
|
|
|
| ||||||||
| Ÿ | “Setting | the | Base | I/O | Address” | on |
| page |
|
|
|
|
|
|
|
|
Ÿ“Setting the Interrupt Level” on page
Setting the |
|
|
|
| Bus | Width: | Switch 10 (BW) sets the width of the data bus. | If the adapter is in an | ||||||||||||||||||||||||||||
ISA | slot | connector), | the | switch must | be | set | to an | data | bus. If t | |||||||||||||||||||||||||||
slot, |
|
| the |
|
| switch | can | be set to | an | or | data | bus. |
|
|
| |||||||||||||||||||||
Note: |
|
| All IBM | ARTIC | adapters in | a | system | must be | set to | the | same | width. |
| |||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Switch | 10 (BW) | Data Bus Width |
|
|
|
On |
| |
|
|
|
Off |
| |
|
|
|
Figure |
Installation and