IBM Heritage - page 23

2-8 Installin

g

and Confi

g

urin

g

y

our xDSL Router

4. Confirm if the TCP/IP protocol has been correctly setup with

your Ethernet card.

Contents

Main Heritage Series Page Table of Contents Page Page Chapter 1 Introduction 1.1 1.2 Features and Compatibility Page 1.3 Whats in the package? 1.4 Important Rules for Safe Operation Page Page 1.5 Front Panel 1.6 Rear Panel Page Page 2.1 Preparation for Hardware and software installation Page 2.2 Hardware Installation 2.3 Windows 95/98 setting for Ethernet LAN connection 2.3.1 Check TCP/IP protocol Page 2.3.2 TCP/IP installation Page 2.3.3 TCP/IP setting Page Page 2.4 Configuring the Router 2.4.1 Using TELNET via Ethernet interface 2.4.2 Using terminal program via serial console port Page Page Page Page 3.1 Factory default configuration 3.2 Bridged RFC1483 (Default configuration for Router) Page 3.3 Routed RFC1483 3.4 Classical IP (RFC1577) Page 3.5 PPP Over ATM (RFC2364) Page Page Page 3.6 PPP Over Ethernet (RFC2516) Page Page 4.1 Add NAT to Classic IP, PPP over ATM or PPP over Ethernet Page Page Page 4.3 Changing DHCP server configuration Page Page 4.4 Changing DHCP client configuration Page 4.5 PPTP Tunneling Configuration Page Advanced Confi g urations Page Chapter 5 Managing the xDSL Router 5.1 Booting the xDSL Router from Ethernet Network 5.2 Upgrading on-board flash memory from Ethernet network ( 5.3 SNMP Page Page Page Page Basic system command sets 1. <process>, <process> <command> 2. help Page Commands for ISFS and FLASHFS process 1. ISFS and FLASHFS overview 2. isfs cat | flashfs cat 3. isfs ls | flashfs ls 4. isfs rm 5. flashfs update Commands for Bridge process 1. device add 2. device delete 3. device list 4. ethertype 5. filter 6. filterage 6. flush 7. portfilter 8. status 9. spanning disable | enable 10. spanning forwarddelay 11. spanning hellotime 12. spanning maxage 13. spanning port <number> 14. spanning port <number> disabled | enable 15. spanning port <number> pathcost Page 18. spanning status Commands for DHCP server process 1. dhcpserver config 2. dhcpserver status Commands for DHCP Client process 1. dhcpclient config 3. ip device 2. dhcpclient status Commands for IP process 1. arp 2. config 3. device Page Page 4. disable 5. enable 6. get 7. ipatm abort 8. ipatm arp 9. ipatm arpserver 10. ipatm files 11. ipatm lifetime 12. ipatm pvc 13. iphostname 14. norelay 15. ping 16. portname 17. relay 18. rip accept 19. rip allowed 20. rip boot 21. rip hostroutes 22. rip killrelay 23. rip poison 24. rip relay 25. rip relays 26. rip send 27. route Page 28. routeflush 29. routes 30. stats 31. subnet Page Commands for NAT process 1. ip nat 2. nat interfaces 3. nat inbound 4. nat info 5. nat protocol 6. nat sessions 7. nat stats Commands for PPP process 1. Console object types 1.1 Channels 1.2 Users 1.3 Interfaces 3. <channel> disable 4. <channel> discard 5. <channel> echo 6. <channel> echo every 7. <channel> enable 8. <channel> hdlc 9. <channel> info 10. <channel> interface 11. <channel> lcpmaxconfigure 12. <channel> lcpmaxfailure 13. <channel> lcpmaxterminate 14. <channel> llc 15. <channel> pvc 16. <channel> qos 17. <channel> remoteip 18. <channel> svc 19. <channel> theylogin 20. <channel> welogin 21. bcp 22. interface <n> localip 23. interface <n> stats 24. user Commands for SNMP configuration 1. access 2. config 3. trap Commands for DSL process 1. show rate 2. show defect 3. down 4. up 7. mode glite 8. mode gdmt-dbm 9. mode gdmt-fbm 10. mode glite-dbm 11. mode glite-fbm Page 19. show perf 20. show id Page Chapter 8 DHCP Server Operation 8.1 DHCP Server overview 8.2 DHCP Server Configuration 8.3 Informal configuration guide 8.3.1 Subnets 8.3.2 Lease Length 8.3.3 BOOTP Support 8.3.4 Options 8.4 Configuration reference guide 8.4.1 Network topology 8.4.2 Declarations 8.4.3 ALLOW and DENY 8.4.4 Parameters Page Page 8.4.5 Option statements Page Page Page Page Page Page Page Page 9.1 Protocol Timing 9.1.1 Timeout 9.1.2 Retry 9.1.3 Select-timeout 9.1.4 Reboot 9.1.5 Backoff-cutoff 9.1.6 Initial-interval 9.2 Lease requirements and requests 9.2.1 Request 9.2.2 Require 9.2.3 Send 9.3 Other declarations 9.3.1 Reject 9.3.2 Interface 9.4 DHCP Options 9.4.1 Option statements 9.4.2 Supported DHCP client options Page Page Page Power Adaptor Page B.2 Problems when configure the Modem via the console port B.3 Problems when connecting to the Modem via Ethernet B.4 Problems when accessing the Internet or remote network B.5 Contact us for Technical support Page Page Page Page Page Page Page Page Page D.2 DOC compliance information D.3 European CTR 21 compliance