Manuals / IBM / Computer Equipment / Network Router

IBM Heritage user manual PPP Over ATM RFC2364, This is the login name and password of PPP server

Models: Heritage

1 167

Download 167 pages 57.31 Kb

Page 40

Heritage Series ADSL Bridge/ Router	3-9
Basic Configurations

3.5 PPP Over ATM (RFC2364)

[System configuration]

Ethernet

202.1.136.100

	Ethernet Port	192.168.
	202.1.136.254
		1.2

	[ISP/DSLAM Configuration]
	IP Address :	192.168.1.1	DSLAM/NSP
	Subnet Mask :	255.255.255.0	DSLAM/NSP
	Subnet Mask :	255.255.255.0	192.168.1.1
	Default Gateway :	192.168.1.2	192.168.1.1
	Default Gateway :	192.168.1.2
	[Local PC Configuration]
	IP Address :	202.1.136.100
	Subnet Mask :	255.255.255.0
	Default Gateway :	202.1.136.254

The xDSL Router also can be setup to support RFC 2364(PPP over ATM) with following procedure. Before setup RFC 2364, you have to ensure remove existing RFC 1483 or RFC 1577 configuration with the procedure mentioned above.

•IP dial out over PPPoA

>ip device add Ethernet ether //edd 202.1.136.254 ↵

(This is the IP of Ethernet port of xDSL Router)

>ip device add ppp_device ether //ppp/DEVICE=1 ↵

>config save ↵

>restart ↵

>ppp 1 pvc 0 32 ↵

(Set channel 1 to VPI=0, VCI=32)

>ppp 1 welogin <name> <password> ↵

(This is the login name and password of PPP server)

>ppp 1 enable ↵

Image 40

IBM Heritage user manual PPP Over ATM RFC2364, This is the login name and password of PPP server

Contents

Heritage Series Copyright Table of Contents Managing The xDSL Router Dhcp Client Configuration Chapter OverviewFeatures and Compatibility Heritage Series Adsl Bridge/ Router Introduction What’s in the package? Important Rules for Safe Operation Turn Off the Power Switch Between DC Plug Off and On Heritage Series Adsl Bridge/ Router Introduction Front Panel Function Behavior DefinitionRear Panel Function Definition10Introduction Installing Configuring your xDSL Router Preparation for Hardware and software installation DSLAM/ISPPC a HUB PC B Hardware Installation Check TCP/IP protocol Windows 95/98 setting for Ethernet LAN connectionDouble-click on My computer-Control Panel-Network Installing and Configuring your xDSL Router 2 TCP/IP installation Installing and Configuring your xDSL Router 3 TCP/IP setting Your network manager for correct configurationsInstalling and Configuring your xDSL Router For example Click OK to save the new setting Using Telnet via Ethernet interface Configuring the RouterSelect Start-Programs-MS-DOS Prompt Using terminal program via serial console port Select Start-Programs-Accessories-HyperTerminalInstalling and Configuring your xDSL Router Installing and Configuring your xDSL Router Installing and Configuring your xDSL Router Basic Configurations Factory default configuration AdminBridged RFC1483 Default configuration for Router System configurationISP/DSLAM configuration Local PC configurationIsfs rm resolve Isfs rm initbridge Isfs rm initppp Restart Local PC B configuration Local PC a configurationRouted RFC1483 Is the IP address of your service provider Classical IP RFC1577 Use the same VPI/VCI of RFC 1577 setting This is the login name and password of PPP server PPP Over ATM RFC2364Remote bridging over PPPoA Basic Configurations Basic Configurations PPP Over Ethernet RFC2516 Ip relay all Config save Restart Advanced Configurations Local PC 8 configuration Local PC 1 configurationAdd NAT to Classic IP, PPP over ATM or PPP over Ethernet Ip nat add ipoa 202.1.136.254 102.2 Add NAT to RFC 1483 to above RFC 1483 Routing Mode example Changing Dhcp server configuration Deletes current Dhcp server settings Restart Home Dhcpclient config Changing Dhcp client configurationDhcpclient config flush Dhcpclient config confirm Pptp Tunneling Configuration Set channel 2 to VPI=0, VCI=32Set channel 2 to VPI=0, VCI=32 Pptp bind none Config save Restart Advanced Configurations Router Configuration Booting the xDSL Router from Ethernet NetworkManaging the xDSL Router This command is available for update boot code only Upgrading on-board flash memory from Ethernet networkSnmp Managing the xDSL Router XDSL Link Performance Statistics XDSL Link Performance Statistics Command Sets for Command Line Interface Command line interface conventionsBasic system command sets Process, process commandHelp DSL conifgRestart History mechanismSystem Isfs and Flashfs overview Commands for Isfs and Flashfs processIsfs cat flashfs cat Isfs ls flashfs ls Flashfs updateIsfs rm Commands for Bridge process Device addDevice delete Forum LAN emulation alecjadeDevice list EthertypeFilterage FilterFlush Portfilter Spanning forwarddelay Spanning disable enableStatus Spanning hellotime Spanning maxageSpanning port number Spanning port number disabled enableSpanning port number pathcost Spanning port number priority Spanning prioritySpanning status Commands for Dhcp server process Dhcpserver config DSL dhcpserver configDhcpserver status IP address Client UID ExpiryDhcpclient status Commands for Dhcp Client process Dhcpclient configIp device Commands for IP process Arp DSL ip arp add ether 192.168.50.1 8020199AD9Config DeviceEthernet IP-over-ATM Disable EnableGet Ipatm abortIpatm arp Ipatm arpserverIpatm files Ipatm lifetimeIpatm pvc Iphostname NorelayPing PortnameCommand RelayRip accept Rip allowedRip boot Rip hostroutesRip killrelay Rip poisonRip relay Rip relaysRip send RouteExample Routeflush RoutesStats SubnetDSL ip subnet Commands for NAT process Ip natNat interfaces Nat inboundNat info Nat inbound add pppdevice 80/TCP Nat inbound listNat protocol Nat sessionsNat stats Nat sessions pppCommands for PPP process Console object typesChannel disable Channel echo every Channel lcpmaxconfigure Channel lcpmaxfailureChannel lcpmaxterminate Channel llcRead PVC settings for channel Remove any PVC settings fromSet channel 3 to be VPI=3,VCI=32 ChannelChannel remoteip Channel theylogin Bcp Interface n localipInterface n stats UserCommands for Snmp configuration AccessTrap Commands for DSL process Mode glite Mode gdmt-dbmMode gdmt-fbm Mode glite-dbmMode cpe-a Mode cpe-bMode co-ab Mode co-aShow perf Show idCommand Sets for Command Line Interface Dhcp Server Operation Dhcp Server overviewInformal configuration guide Dhcp Server ConfigurationSubnets Bootp Support Lease LengthConfiguration reference guide OptionsNetwork topology Subnet DeclarationsRange Allow and Deny HostGroup Unknown-clientsParameters Dynamic-bootp-lease-cutoff FilenameServer-name server-name name Next-serverDynamic-bootp-lease-length Use-host-decl-namesOption statements Server-identifierOption time-offset int32 This specifies the IP address of the client’s swap server Option max-dgram-reassembly uint16 Subnet Option arp-cache-timeout uint32 Preference Dhcp Server Operation Configuration Chapter Dhcp ClientTimeout Select-timeoutProtocol Timing RetryReboot Backoff-cutoffInitial-interval Lease requirements and requestsRequest RequireSend Other declarations RejectInterface Dhcp OptionsOption domain-name isc.org Supported Dhcp client options Dhcp Client Configuration Appendix a Product Specifications Appendix Power Adaptor Appendix B Troubleshooting Diagnostics with the LEDsIf the Power LED is dark If the PC LED is darkProblems when configure the Modem via the console port Problems when connecting to the Modem via EthernetCan’t see any message from the configuration screen Junk characters appear on the configuration screenIf the Modem is configured to bridging mode Problems when accessing the Internet or remote networkIf the Modem is configured to routing mode Contact us for Technical support Appendix C 10Base-T100Base-T Ansi American National Standards InstituteClass A, B, and C networks ClientCommunity strings Console portEthernet address FirmwareInternet Internet address, IP addressMAC layer/address PingPort number ProtocolRFC RJ-11RJ-45 RoutingSerial port ServerSubnet Address Subnet maskTransparent Bridging Virtual ChannelVirtual Path Wall jackWAN Appendix D Government compliance notices FCC complianceDOC compliance information European CTR 21 compliance