Cleaning and Special Maintenance
The filter assembly
If you want consistent good results from your dishwasher, you need to clean the filter assembly; this way the food particles are removed from the wash water, allowing it to be recirculated during the cycle, filtered perfectly. For this reason, it is a good idea to remove the larger food particles trapped
inside the cup “C” and | |||
wash. All you need to do is |
|
|
|
rinse them under running |
|
|
|
| 1 |
| |
water; to remove these, pull |
|
| |
|
| A | |
the cup handle upwards. | B | 2 | |
The entire filter assembly, |
|
|
|
comprising a |
|
|
|
filter “A”, a cup “C”, and a |
|
|
|
cylindrical filter “B” should |
| C |
|
be cleaned thoroughly once |
|
| |
|
|
| |
a month. Rotate filter “B” |
|
|
|
anticlockwise to remove it. For cleaning, use a non metallic brush.
Reassemble the three parts as shown in the figures and reinsert the whole assembly into the dishwasher, positioning it into its housing and pressing downwards.
The dishwasher is not to be used without filters. Improper replacement of the filters may reduce the efficiency of the wash and even damage your dishwasher.
Cleaning the Sprayer Arms
It may happen that food particle become encrusted on the sprayer arms and block the holes (see "Close up view (interior)", letters
Troubleshooting
It may occur that the dishwasher does not function or does not function properly. Before calling for assistance, let us see what can be done first: have you forgot to press one of the buttons or to perform an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
-the plug is pushed into the socket correctly;
-the power is on in the house;
-the door is closed properly;
-the
-the water supply is turned on.
The Dishwasher Does Not Load Water
Have you checked whether:
-the water is turned on and the hose is connected properly;
-the water supply to the house is on and has sufficient pressure;
-the water supply hose is crimped or bent;
-the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you put the right amount of detergent into the dispenser?
Is the wash cycle suitable for the dishes you have placed inside the appliance?
Are the filter and microfilter clean? Can the sprayer arms turn freely?
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes Have you checked whether:
-the lid to the salt container is closed properly;
-the rinse aid dosage is correct.
If the display indicates the word "dON" when you turn your dishwasher on, this means the demo mode is in operation.
Read the instructions on pages 18.
Error messages.
Your dishwasher is equipped with a safety system which is able to detect any operating anomalies.
These anomalies or faults are signalled by several codes consisting of letters and numbers that flash up on the display. Make a note of the error code that appears, turn the appliance off, turn off the water tap and call for technical assistance.
Tap off alarm
If you have forgotten to turn on the water tap, the appliance will remind you with a series of prolonged beeps and the wording H2O will flash up on the display. Turn the tap on and the wash cycle will start up after a few minutes.
If you are not there when the H2O signal appears, the appliance will switch to alarm mode and the code "A06" will flash on the display. Turn the appliance off at button "A", turn on the water tap and wait approximately 20 seconds before turning the appliance back on, the wash cycle will start up again.
Clogged filter alarm
If the appliance is blocked and the code "A05" is flashing, this means the filter is clogged by large particles of food residue. Turn the appliance off at the
Water load solenoid valve malfunction alarm
If the code "A02" flashes, first of all turn off the water tap to avoid any flooding and then cut off the electricity supply and call for assistance.
If, despite all these checks, the dishwasher still does not function and/or the problem persists, contact the nearest authorised service centre and provide them with the following information:
-the nature of the problem;
-the model type number (Mod. ...) and the serial number (S/N ....), which are indicated on the plate located on the side of the inner part of the door.
Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts.
21 | GB |
