Installation

Positioning the Appliance

Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the dishwasher, making it level. In any case, the appliance should not be inclined more than 2°.

Drain Hose Connection

Fit the drain pipe into a drain line with a minimum diameter of 4 cm or place it over the sink. Avoid restricting or bending it. Use the special plastic elbow provided (see fi- gure) to position it in the best possible way. The part of the pipe marked with the letter A should be between 40 and 100 cm above the ground.

A

If the appliance is level, it will help ensure proper perfor- mance.

This dishwasher model can be built under a single worktop (please read the relevant instruction sheet).

Cold water connection.

Connect the cold water supply hose to a 3/4 gas threaded connection, taking care to screw it tightly onto the tap. If the water hoses are new or have been out of use for an extended period of time, let the water run to make sure it is clear and free of impurities before making the connection. If this precaution is not taken, the water inlet could get blocked, causing damage to your dishwasher.

Hot Water Connection

The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60° C.

In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line.

Anti-flooding protection

Your dishwasher is provided with a special system which blocks the water supply in the event of leaks inside the appliance. It is further equipped with a water inlet hose that can withstand extremely high pressures and that turns bright red in the event of breakage. Safety in the event of flooding is ensured by the second clear hose that contains the former and thus highlights the latter when it has turned bright red. It is vital that you check it on a regular basis: if you see it has turned bright red, then you know you have to replace it as soon as possible. Call for an authorised technical engineer to come and replace it.

The pipe should not be immersed in water.

Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is sized for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug, rather than using adpators or the like as they could cause overheating and burns.

Should the electricity supply cable be damaged, we recommend that you only contact authorised Technical Service Centres for the replacement.

GB

22

Page 24
Image 24
Indesit IDE 45 manual Installation

IDE 45 specifications

The Indesit IDE 45 is a compact and efficient built-in double oven designed to meet the demands of modern cooking. With a focus on practicality and performance, this appliance is ideal for those who have limited kitchen space but still desire a multifunctional cooking solution.

One of the standout features of the Indesit IDE 45 is its impressive capacity. The double oven design allows users to cook multiple dishes simultaneously, maximizing efficiency during meal prep. The top oven has a conventional cooking option, ideal for baking and roasting, while the lower oven features a fan-assisted design that ensures even heat distribution, resulting in perfectly cooked meals every time.

Energy efficiency is a key characteristic of the IDE 45. It boasts an A energy rating, meaning it effectively reduces power consumption without compromising on performance. This not only contributes to lower energy bills but also supports environmentally friendly cooking practices.

The user-friendly interface of the Indesit IDE 45 is another highlight. It features easy-to-use knobs and a digital display that allows users to select the desired temperature and cooking settings with ease. The appliance also includes a timer function that ensures meals are cooked to perfection, reducing the risk of overcooking or burning.

Indesit has incorporated innovative cooking technologies into the IDE 45. The Rapid Cooking feature allows users to preheat the oven in no time, making it perfect for those busy evenings when time is of the essence. Furthermore, the integrated grill function provides versatility in cooking, enabling users to achieve crispy finishes on their dishes.

Cleaning the Indesit IDE 45 is hassle-free, thanks to its easy-clean enamel lining that reduces the buildup of grease and food residues. The removable oven shelves and trays make it convenient to maintain the cleanliness of the appliance, ensuring it remains in great condition for years to come.

In summary, the Indesit IDE 45 combines size, efficiency, and technology to offer an ideal cooking solution for those seeking practicality in the kitchen. With its dual oven design, energy efficiency, user-friendly controls, rapid cooking capabilities, and easy maintenance, the IDE 45 is a compelling choice for both novice and experienced home cooks alike.