Manuals / InFocus / Computer Equipment / Projector

InFocus LPTM425z warranty Manual Tracking, Horizontal position, Vertical position

Models: LPTM425z

1 62

Download 62 pages 4.97 Kb

Page 32

Manual Tracking

Manual Tracking

The projector adjusts tracking automatically to match the video signal from your computer. However, if the display shows evenly spaced, fuzzy, vertical lines or if the projected image is too wide or too narrow for the screen, try turning Auto Image off then back on again. If the image is still bad, try adjusting the tracking man- ually:

1Turn Auto Image off.

2Highlight Manual tracking, the press either mouse button repeatedly until the fuzzy vertical bars are gone.

Positioning adjustments are saved when you power off the pro- jector.

Horizontal position

Follow these steps to manually adjust the horizontal position:

1Turn Auto Image off.

2Highlight Horizontal position, then press the left mouse but- ton to move the image right or press the right mouse button to move the image left.

Positioning adjustments are saved when you power off the pro- jector.

Vertical position

Follow these steps to manually adjust the vertical position.

1Turn Auto Image off.

2Highlight Vertical position, then press the left mouse button to move the image down or press the right mouse button to move the image up.

Positioning adjustments are saved when you power off the pro- jector.

NOTE: The Manual Sync,

Manual Tracking, Horiz. Posi-

tion and Vert. Position options are available only for computer sources. The projector sets these options automatically for a video source.

29

Image 32

InFocus LPTM425z warranty Manual Tracking, Horizontal position, Vertical position

Contents

TABLE OF CONTENTS Safety InstructionsSetting up the Projector Using the ProjectorAppendix IndexSpecifications AccessoriesSAFETY INSTRUCTIONS Warning Hot surface. Do not touchOr, send us an e-mail at techsupport@infocus.com Image Resolution INTRODUCTIONLP425z LP435zdiately if anything is missing CompatibilityUnpacking the Projector Shipping box contents I n t r o d u c t i o n Side view of projectorFront view of projector speakerUsage Guidelines If You Need AssistanceWarranty I n t r o d u c t i o nSETTING UP THE PROJECTOR Connecting the CableWizard3 to the Projector S e t t i n gt h e P r o j e c t o rPage Preparing to Connect Your Equipment to the ProjectorEquipment you want to connect Do you want to play your computer’s audio on the projector? Connecting a Laptop ComputerIf your computer has a PS/2 connector, use the PS/2 mouse cable NOTE The USB mouse is sup- ported for use with Windows 98 only audio cable mouse cableConnecting a Desktop Computer audio cable mouse cable monitor cable Connecting a Video Player audio/video cableS-video cable A/V cable Powering up the Projector and Adjusting the Image Turning Off the Projector Using the Remote Control USING THE PROJECTORBasic Image Adjustment on underside of remote Remote controldisk mouse right mouse button left mouse button Adjusting the Projector Using the Keypad and Remote Buttons MenuMouse buttons Source keypad only or Computer and Video remote onlyIf you don’t press standby again, the lamp turns off after 15 minutes Using the On-Screen Menus Drop-down menuDisplay Menu Blank Screen Reset AllColor Audio Menu Image Menu Manual Tracking Horizontal positionVertical position NOTE The Manual Sync Manual Tracking, Horiz. PosiControls Menu Video StandardStandby Time Ceiling ProjectionDefault Source Rear ProjectionAuto Source Select Plug and PlayLanguage Menu Display Startup ScreenStatus Menu Indicates the active source, Computer or Video Replacing the Projection Lamp MAINTENANCE & TROUBLESHOOTINGCleaning the Lens 4 Pull the lamp door up and remove it 5 Loosen the two non-removable screws on the outside of the moduleM a i n t e n a n c e T r o u b l e s h o o t i n gRemoving the lamp module Sliding the lamp connector7 Remove the module Figure Replacing the Batteries in the Remote Control Using the Kensington Lock Installing the Kensington lockTroubleshooting Problem Nothing on projection screen Problem Color or text not being projectedProblem The screen resolution is not right Problem Image isn’t centered on the screenProblem Image is too wide or narrow for screen Problem Image is out of focus Problem Image and menus are reversed left to rightProblem the projector displays vertical lines, “bleeding” or spots Problem no soundProblem Lamp seems to be getting dimmer Problem Lamp shuts offAPPENDIX Specifications TemperatureDimensions WeightComputer Audio Input A p p e n d iVideo Audio Input Accessories Standard AccessoriesPower Cords one ships with projector, type depends on country ship with the projectorOptional Accessories A p p e n d iPortable and Laptop Activation Chart Key command to Key command toA p p e n d i ComputerKey command to Key command toComputer activate portKey command to Key command toA p p e n d i ComputerKey command to Key command toComputer activate portUsing Video Mirroring with a PowerBook Computer Projected Image Size Projected image size for LP425zImage Size, Width and Height for LP425z-maximum image size Distance toA p p e n d i Projected image size for LP435zImage Size, Width and Height for LP435z-maximum image size Distance toINDEX I n d e Page I n d e