|
|
|
|
|
|
|
| Insignia |
|
|
|
| Programming the remote | ||||
| Category | Problem | Possible Solution | |||||
|
|
|
|
| control | |||
|
| Television |
| • When the television is in use, | ||||
|
| cabinet creaks |
| there is a natural rise in |
|
| ||
|
|
|
|
|
| temperature, causing the | Introduction | |
|
|
|
|
|
| cabinet to expand or contract | ||
|
|
|
|
|
| and may be accompanied by | Your remote lets you control four devices with | |
|
|
|
|
|
| a slight creaking noise. This | one | |
|
|
|
|
|
| is not a malfunction. | ||
|
|
|
|
|
| batteries, you can program the remote to control | ||
|
|
|
|
|
|
| ||
|
| Control buttons |
| • Disconnect the power cord | your VCR or DVD, cable or satellite receivers, | |||
|
| do not operate |
| and wait for a few seconds. | amplifier or tuner, and auxiliary devices. To do | |||
|
|
|
|
|
| Then | so, follow the instructions in “Programming a | |
|
|
|
|
|
| cord and turn on the | Device” For best results, please read and follow | |
|
|
|
|
|
| television again. | ||
|
|
|
|
|
| all the remaining instructions. Keep this guide for | ||
|
|
|
|
|
|
| future reference. | |
|
| Caution |
|
|
|
| ||
|
| Never attempt to repair a defective television |
|
| ||||
|
|
| Note | |||||
|
| yourself. |
|
|
| |||
|
|
|
|
| The universal remote control unit can't be | |||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| programmed to control a different brand of |
|
|
|
|
|
|
|
| television. It has been preset to control this |
|
| Note |
|
| ||||
|
|
|
|
| television set and this preset is unchangeable. | |||
|
| If your problem is not solved, turn your television |
|
| ||||
|
| off and then on again. | Programming a device | |||||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
Specifications
Note
•Design and specifications are subject to change without notice.
•Weight and dimensions shown are approximate.
•Specifications and external appearance may be changed for the sake of improvement.
To control a VCR or DVD, cable or satellite receiver, amplifier or tuner, and auxiliary device, follow these steps. Before proceeding, find the codes for the devices you want to program in the following tables and write them down or highlight them.
Note
To program a DVD player, portable DVD player, or mobile DVD player, use the DVD key.
Type | LCD TV | |
|
| |
Panel | ||
|
| |
TV system | American TV standard ATSC/NTSC system | |
|
| |
Receiving channels | VHF | |
| ||
|
| |
Audio multiplex | BTSC system | |
|
| |
Audio out | 8W x 2 | |
|
| |
Power requirement | AC 120 V. 60 Hz | |
|
| |
Power | 180 W | |
consumption |
|
|
|
| |
Dimensions | 36.7 x 27.5 x | |
| (931 x 699 x 330 mm) | |
|
| |
Weight | 42 lbs/19 kg | |
|
|
|
Input terminals | 2 | Composite Video/Audio (L/R) |
| 1 | |
| 2 | Component Video/Audio (L/R) |
| 2 | HDMI interface |
| 1 | VGA/Audio |
| 1 | Antenna |
|
|
|
Output terminals | 1 | Composite Video/Audio (L/R) |
| 1 | S/PDIF optical digital audio out |
| 1 headphone jack | |
|
|
|
Control terminals | 1 | |
|
|
|
To program a device:
1Turn on the device (for example, the DVD player) and, if needed, load the media (for example, a DVD).
2Press the DVD, CBL, or AUX button.
3Press and hold SET until the red LED blinks twice, then release the button.
4Enter the first
Note
If the LED does not blink twice, repeat steps 2 to 4 and try entering the code again.
5Aim the remote at the device and press Power. The device should turn off. If it does not, repeat steps 3 to 5, trying each code for your brand until you find one that works. If you cannot find a code that works, see “Searching for Your Code”
6Repeat steps 1 to 5 for the other devices you want to control. For future reference, write down each working device code below:
AUX Code: CBL Code: CD Code:
DVD Code: SAT Code: TNR Code: VCR Code:
7Press SET to save your code and exit setup.
22 |