Insignia NS-LCD37 25

Insignia NS-LCD37 LCD TV

Searching for your code

If your device does not respond to the remote after trying all codes listed for your brand, or if your brand is not listed, try searching for your code:

1Press a device key once.

2Press and hold SET until the red LED blinks twice; then release.

3Enter 9-9-1, then the device group number (0= Cable, 1= TV, 2= VCR, 3= Audio). The LED blinks twice.

4Aim the remote at the device and press Power. The remote sends IR codes from its library to the selected device, starting with the most popular code first. If the device responds, go to step 7.

5If the device does not respond, press CH+. The remote will try the next code. Continue until the device responds.

Note

Press CH- to try the previous code.

6To search for other device codes, repeat steps 1 to 5.

7Press SET to save your code and exit setup.

Checking the Codes

If you have set up the remote using the procedure in “Searching for Your Code” you may need to find out which four-digit code is operating your equipment.

To find out which code is assigned to your DVD:

1Press DVD once.

2Press and hold SET until the red LED blinks twice, then release the button.

3Enter 9-9-0. The LED blinks twice.

4To view the code for the first digit, press 1. Count the LED blinks (for example, three blinks = 3), and write down the number in the appropriate code listing in step 6 under “Programming a Device”

To lock volume control to one mode (Global Volume Lock):

1Press and hold SET until the red LED blinks twice, then release the button.

2Enter 9-9-3and then press the mode key for the device you want to control volume (for example, DVD). The LED blinks twice. Now when you press VOL+, VOL-, or Mute, the selected device (for example, DVD) will control the volume regardless of the current mode.

To unlock all volume control (restoring

Global Unlock):

1Press and hold SET until the red LED blinks twice, then release the button.

2Enter 9-9-3and then press VOL+. The LED blinks four times. Volume is now independently controlled for all programmed devices.

To unlock a single device's volume control:

1Press a device key (DVD, CBL, or AUX).

2Press and hold SET until the red LED blinks twice, then release the button.

3Enter 9-9-3and then press VOL-. The LED blinks four times. Volume is now independently controlled for the selected devices.

Troubleshooting

Problem	Solution

LED does not blink	Replace new batteries.
when you press a key.

LED blinks when you	Make sure the remote is aimed at your
press a key, but device	device and is not more than 15 feet away.
does not respond.

LED blinks one long	An entry error has occurred (for example,
blink.	wrong key). Try the entry sequence again.

Remote does not	Try all listed codes for the device. Make
control devices or	sure the device operates with an infrared
commands are not	remote control.
working properly.

Note

If a code digit is 0, the LED does not blink.

5Repeat step 4 for the four remaining digits, using 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit.

6To check for other device codes, repeat steps 1 to 5, substituting the device key for DVD.

Care

•Keep the remote dry. If it gets wet, wipe it dry immediately.

•Use and store the unit only in normal temperature environments.

•Handle the remote gently and carefully. Don't drop it.

•Wipe the remote with a damp cloth to keep it looking like new.

Changing Volume Lock

The remote comes preset to allow independent volume control of each selected device (Global Volume Unlock). However, you may change the Volume Lock setting to Global Volume Lock so that one device's volume will control volume in all other modes. After that, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation or Global Volume Unlock to remove all volume locking.

Manufacturer’s Codes

Audio Amplifiers

Manufacturer Code

Bose30674

GE30078

JVC30331

Marantz 30321

Nakamichi 30321