30.3 Cabling and Termination

Word clock signals are usually distributed in the form of a network, split with BNC T-adapters and terminated with resistors. We recommend using off-the-shelf BNC cables to connect all devices, as this type of cable is used for most computer networks. You will find all the neces- sary components (T-adapters, terminators, cables) in most electronics and/or computer stores. The latter usually carries 50 Ohms components. The 75 Ohms components used for word clock are part of video techology (RG59).

Ideally, the word clock signal is a 5 Volt square wave with the frequency of the sample rate, of which the harmonics go up to far above 500 kHz. To avoid voltage loss and reflections, both the cable itself and the terminating resistor at the end of the chain should have an impedance of 75 Ohm. If the voltage is too low, synchronization will fail. High frequency reflection effects can cause both jitter and sync failure.

Unfortunately there are still many devices on the market, even newer digital mixing consoles, which are supplied with a word clock output that can only be called unsatisfactory. If the output breaks down to 3 Volts when terminating with 75 Ohms, you have to take into account that a device, of which the input only works from 2.8 Volts and above, does not function correctly al- ready after 3 meter cable length. So it is not astonishing that because of the higher voltage, word clock networks are in some cases more stable and reliable if cables are not terminated at all.

Ideally all outputs of word clock delivering devices are designed as low impedance types, but all word clock inputs as high impedance types, in order to not weaken the signal on the chain. But there are also negative examples, when the 75 Ohms are built into the device and cannot be switched off. In this case the network load is often 2 x 75 Ohms, and the user is forced to buy a special word clock distributor. Note that such a device is generally recommended for bigger studios.

The Fireface's word clock input can be high-impedance or terminated internally, ensuring maxi- mum flexibility. If termination is necessary (e.g. because the Fireface is the last device in the chain), push the switch at the back beside the BNC socket (see chapter 30.1).

In case the Fireface 800 resides within a chain of devices receiving word clock, plug a T- adapter into its BNC input jack, and the cable supplying the word clock signal to one end of the adapter. Connect the free end to the next device in the chain via a further BNC cable. The last device in the chain should be terminated using another T-adapter and a 75 Ohm resistor (avail- able as short BNC plug). Of course devices with internal termination do not need T-adaptor and terminator plug.

Due to the outstanding SteadyClock technology of the Fireface 800, we recommend not to pass the input signal via T-adapter, but to use the Fireface's word clock output instead. Thanks to SteadyClock, the input signal will both be freed from jitter and - in case of loss or drop out – be reset to a valid frequency.

30.4 Operation

The green Lock LED on the front (DIGITAL STATE) will light up as soon as a word clock signal is detected. To change to word clock as clock source, activate clock mode AutoSync and switch Pref. Sync Ref to Word Clock within the Settings dialog. The status display AutoSync Ref changes to Word as soon as a valid signal is present at the BNC jack. This message has the same meaning as the green Lock LED, but appears on the monitor, i.e. the user can check immediately whether a valid word clock signal is present and is currently being used.

AutoSync Ref also displays the frequency (Freq.) of the reference signal, here the frequency of the current word clock signal, measured by the hardware.

62

User's Guide Fireface 800 © RME

Page 61 Page 63
Page 62
Image 62
Intel Fireface 800 manual Cabling and Termination, Operation
Page 61 Page 63

Fireface 800 specifications

The Intel Fireface 800 is a powerful audio interface celebrated for its high-performance capabilities and versatility in both studio and live settings. Designed to cater to the needs of musicians, producers, and sound engineers, it stands out with its rich feature set and reliable technology.

One of the defining features of the Fireface 800 is its support for an impressive 26 input and 28 output channels. This extensive I/O configuration facilitates seamless integration with a wide variety of audio production setups, allowing users to record multiple instruments simultaneously or create complex routing scenarios. The unit also boasts top-notch analog and digital converters, ensuring pristine sound quality with a dynamic range that captures the nuances of any audio source.

In terms of connectivity, the Fireface 800 is equipped with both FireWire and USB ports, making it compatible with a range of computers and devices. The device utilizes the FireWire 800 protocol, which delivers higher data transfer rates compared to its predecessor. This efficient transfer capability is crucial for maintaining audio fidelity and reducing latency, making it an ideal choice for real-time monitoring and recording.

The Fireface 800 also features standalone operation capabilities, functioning independently of a computer when needed. This is particularly useful for live performances, where reliability and reduced setup complexity are essential. Users can easily connect microphones, instruments, and other equipment directly to the Fireface 800, making it a versatile tool for a variety of scenarios.

With its low-latency driver technology, the Fireface 800 ensures smooth performance even when handling demanding audio tasks. Its advanced ADAT and S/PDIF digital inputs and outputs provide further flexibility for connecting other gear, such as additional preamps and effects processors.

Another noteworthy characteristic of the Fireface 800 is its robust build quality. Designed for regular use in professional environments, the unit features a rugged metal chassis that can withstand the rigors of transport and daily use. This ensures longevity and consistent performance for audio professionals who depend on reliable equipment day in and day out.

In summary, the Intel Fireface 800 is a versatile and powerful audio interface that caters to a wide spectrum of audio production needs. With its extensive I/O capabilities, high-quality converters, reliable connectivity options, and robust design, it continues to be a popular choice among audio professionals striving for excellence in their work.
Top Page Image Contents