English

2-3

Integrated Peripherals

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

 

Integrated Peripherals

 

 

 

On-Chip Primary PCI IDE

[Enabled]

 

Item Help

 

On-Chip SATA Mode

 

[Auto]

 

Menu Level`

x

PATA IDE Set to

 

Ch.0 Master/Slave

 

 

 

SATA Port 0/2 Set to

 

Ch.2 Master/Slave

 

 

 

SATA Port 1/3 Set to

 

Ch.3 Master/Slave

 

 

 

USB Controller

 

 

[Enabled]

 

 

 

 

USB 2.0 Controller

 

[Enabled]

 

 

 

 

USB Keyboard Support

 

[Enabled]

 

 

 

 

USB Mouse Support

 

[Enabled]

 

 

 

 

Azalia Codec

 

 

[Auto]

 

 

 

 

]

 

 

 

 

 

 

 

Onboard H/W 1394

 

[Enabled]

 

 

 

 

Onboard H/W LAN

 

[Enabled]

 

 

 

 

Onboard LAN Boot ROM

 

[Disabled]

 

 

 

 

Onboard Serial Port 1

 

[3F8/IRQ4]

 

 

 

Onboard Parallel Port

 

[378/IRQ7]

 

 

 

Parallel Port Mode

 

[ECP+EPP]

 

 

 

ECP Mode Use DMA

 

[3]

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

 

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

On-Chip Primary PCI IDE

 

 

 

 

 

Enabled

 

Enable onboard 1st channel IDE port. (Default value)

 

 

Disabled

 

Disable onboard 1st channel IDE port.

 

 

 

On-Chip SATA Mode

 

 

 

 

 

Disabled

 

Disable this function.

 

 

 

 

Auto

 

BIOS will auto detect. (Default value)

 

 

 

Combined

 

Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on the

 

 

 

motherboard; 2 for SATA and the other for PATA.

 

 

Enhanced

 

Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6 HDDs

 

 

 

to use; 4 SATA HDDs plus PATA HDDs.

 

 

 

Non-Combined

Set On-Chip SATA mode to Non-Combined, SATA will be simulated to PATA

 

 

 

mode. Support a maximum of 4 SATA devices. PATA devices will be ignored.

PATA IDE Set to

Ch.0 Master/Slave Set PATA IDE to Ch. 0 Master/Slave. (Default value)

Ch.1 Master/Slave Set PATA IDE to Ch. 1 Master/Slave.

SATA Port 0/2 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 1 Master/Slave, this function will auto set to Ch. 0 Master/Slave.

SATA Port 1/3 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 0 Master/Slave, this function will auto set to Ch. 1 Master/Slave.

USB Controller

Enabled

Enable USB controller. (Default value)

Disabled

Disable USB controller.

GA-8I915PM-FS Motherboard

- 30 -

Page 30
Image 30
Intel GA-8I915PM-FS Integrated Peripherals, Pata IDE Set to, Sata Port 0/2 Set to, Sata Port 1/3 Set to, USB Controller