Manuals / Intel / Computer Equipment / Personal Computer

Intel GA-N680SLI-DQ6 user manual PCIE12V Power Connector, English, Pwrfan

Models: GA-N680SLI-DQ6

1 112

Download 112 pages 13.88 Kb

Page 25

3)PCIE_12V (Power Connector)

3)PCIE_12V (Power Connector)

This power connector provides extra power to the onboard PCI Express x16 slot. When installing two graphics cards, please connect the power cable from the power supply to this connector, or system instability may occur.

	1	PIin No.	Definition
	1	1	NC
		1	NC
		2	GND
		3	GND
		4	+12V

English

4/5/6) CPU_FAN / SYS_FAN / PWR_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(CPU_FAN/ SYS_FAN) power connector and possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND).

Remember to connect the CPU/system/power fan cable to the CPU_FAN/SYS_FAN/PWR_FAN connector to prevent CPU damage or system hanging caused by overheating.

				CPU_FAN / SYS_FAN :
				Pin No.	Definition
				1	GND
				2	+12V / Speed Control
	1			3	Sense

				4	Speed Control
	CPU_FAN / SYS_FAN			4	Speed Control
	CPU_FAN / SYS_FAN			PWR_FAN :
				PWR_FAN :

1

PWR_FAN

Pin No.	Definition
1	GND
2	+12V
3	Sense

- 25 -

Hardware Installation

Image 25

Intel GA-N680SLI-DQ6 PCIE12V Power Connector, 4/5/6 CPUFAN / SYSFAN / PWRFAN Cooler Fan Power Connector, English, Pwrfan

Contents

Users Manual GA-N680SLI-DQ6Intel Pentium D / Pentium 4 LGA775 Processor Motherboard GA-N680SLI-DQ6 May. 08 MotherboardMotherboard Product Manual Classification CopyrightTable of Contents Chapter 4 Appendix Chapter 3 Drivers Installation4-1-1 4-1-2Optional Accessories Item ChecklistGA-N680SLI-DQ6 GA-N680SLI-DQ6 Motherboard Layout100 MHz Block Diagram1-1 Considerations Prior to Installation Chapter 1 Hardware InstallationInstallation Notices Instances of Non-WarrantyEnglish Feature SummaryCoreTM 2 Quad / CoreTM 2 Duo / Pentium processor Extreme Edition Š Supports dual channel DDRII 800/667/533 unbuffered DIMMs NoteEnglish 24-pin ATX power connectorEnglish Additional Features1-3-1 Installation of the CPU 1-3 Installation of the CPU and CPU CoolerEnglish English 1-3-2 Installation of the CPU CoolerMale Push Pin The top of Female Push Pin Female Push Pin English 1-4 Installation of MemoryNotch DDRII English Dual Channel Memory Configuration2 memory modules 4 memory modulesEnglish 1-5 Installation of Expansion CardsEnglish 1-6 Connecting the e-SATA Cable Kittor on the bracket English 1-7 Setup of SLI Scalable Link Interface ConfigurationBefore you begin connector Connecting Two Graphics Cardsplace this part on the top of the bridge connector retention bracket EnglishEnglish Graphics Card Driver SettingIEEE 1394 Port 4 Pins Connector PS/2 Keyboard and PS/2 Mouse Connector1-8 I/O Back Panel Introduction COMAMIC In 1-9 Connectors IntroductionEnglish English 1/2 ATX12V2X / ATX Power Connector+5V Only for 24-pin ATX GNDOnly for 24-pin ATX4/5/6 CPUFAN / SYSFAN / PWRFAN Cooler Fan Power Connector 3 PCIE12V Power ConnectorEnglish PWRFAN7 NBFAN North Bridge Fan Header 8 FDD Floppy ConnectorEnglish English 9 IDE IDE ConnectorEnglish 12 PWRLED14 FPANEL Front Panel Jumper 13 BATTERYSpeaker Connector Switch16 CDIN CD IN Connector 15 FAUDIO Front Audio ConnectorEnglish 18 F USB1 / FUSB2 / FUSB3 Front USB Connector 17 SPDIFIN S/PDIF In ConnectorEnglish 20 LPT Connector 19 F11394 / F21394 Front IEEE 1394 ConnectorEnglish 22 CI Chassis Intrusion, Case Open 21 TPM Connector Trusted Platform ModuleEnglish Please contact your nearest dealer for optional TPM cableEnglish 23 CLRCMOS Clear CMOSOpen Normal Short Clear CMOS Status Page Setup Menu / Option Page Setup Menu Chapter 2 BIOS SetupCONTROL KEYS Main MenuF9 Xpress Recovery2 DEL BIOS Setup/Dual BIOSF12 Boot Menu Startup ScreenBIOS Setting Recovery The Main Menu For example BIOS Ver. FAa„ Standard CMOS Features „ Advanced BIOS Features„ Load Optimized Defaults „ Load Fail-Safe Defaults„ Set Supervisor Password „ Set User PasswordDate Standard CMOS FeaturesTime IDE Channel 0 Master, SlaveDrive A Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced BIOS FeaturesFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Note HDD S.M.A.R.T. CapabilityLimit CPUID Max. to 3 Note No-Execute Memory ProtectNotex ECP Mode Use DMA Integrated PeripheralsEnglish Serial-ATA RAID Config IDE Prefetch ModeOn-Chip IDE Channel0 NV Serial-ATA ControllerOnboard SATA-II Ctrl1 Mode Onboard SATA-II Ctrl1 GSATAII1-0 / GSATAII1-1 connectorsOnboard SATA-II Ctrl2 GSATAII2-0 / GSATAII2-1 connectors Onboard SATA-II Ctrl2 ModeWhen LAN Cable Is Functioning Normally On-Chip SMART LAN LAN Cable Diagnostic Function For LAN1/LAN2When a Cable Problem Occurs When No LAN Cable Is AttachedOnboard Audio Function Onboard LAN Boot ROMOn-Chip USB USB Keyboard SupportECP Mode Use DMA Parallel Port ModeOnboard Parallel Port Enable onboard LPT port and address is 378/IRQ7. Default valuePower-On by Alarm Power Management SetupACPI Suspend Type PME Event Wake UpPower On By Keyboard Power On By MouseKB Power ON Password HPET Support NotePCI 1 IRQ Assignment PnP/PCI ConfigurationsPCI 2 IRQ Assignment PCI 3 IRQ AssignmentCurrent CPU/SYSTEM/POWER FAN Speed RPM Current System/CPU TemperatureCPU Warning Temperature CPU/SYSTEM/POWER FAN Fail WarningCPU Smart FAN ControlNote CPU Smart FAN ModeSystem Smart FAN Control on CPU temperature. Users can adjust the fan speed with Easy TuneMB Intelligent TweakerM.I.T System Clock SettingEnglish SLI-Ready Memory FSB-Memory Clock ModeFSB-Memory Ratio CPU Host FrequencyCPU Clock Ratio Note Robust Graphics BoosterSystem Voltage Control DDR2 Voltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsEnglish English 2-10 Set Supervisor/User Password2-12 Exit Without Saving 2-11 Save & Exit SetupType Y will quit the Setup Utility without saving to RTC CMOS Type N will return to Setup UtilityGA-N680SLI-DQ6 Motherboard English3-1 Install Chipset Drivers Chapter 3Drivers InstallationEnglish 3-3 Driver CD Information 3-2 Software ApplicationsEnglish 3-5 Contact Us 3-4 Hardware InformationDrivers Installation EnglishGA-N680SLI-DQ6 Motherboard English4-1 Unique Software Utilities Chapter 4 Appendix4-1-1 EasyTune 5 Introduction User Interface OverviewHow to use the Xpress Recovery2 4-1-2 Xpress Recovery2 IntroductionSystem requirements English2. BACKUP 1. RESTORE4. REBOOT PrecautionsA. What is Dual BIOS Technology ? 4-1-3 Flash BIOS Method IntroductionB. How to use Dual BIOS and Q-Flash Utility? EnglishHalt On Error DisableDefault, Enable Boot From Main BIOSDefault, Backup BIOSWide Range Protection DisableDefault, Enable Auto Recovery EnableDefault, DisableMethod 1 Q-FlashTM Updating the BIOSBefore Use EnglishEnglish c . Select the BIOS file and press ENTEREnglish 1. Methods and steps Method 2 @BIOSTM UtilityEnglish English 2. NoteTo configure SATA hard drives, follow the steps below 4-1-4 Configuring SATA Hard Drives1 Installing SATA hard drives in your computer A. nVIDIA nForce 680i SLI SouthbridgeEnglish 2 Configuring SATA controller mode and boot sequence in BIOS SetupEnglish MediaShield ROM BIOS Copyright C 2006 NVIDIA Corp Detecting array 3 Configuring RAID set in RAID BIOSPress F10 to enter RAID setup utility EnglishEnglish Next, select the hard drives which you wish to be included in the disk array. The Free Disks section displays the information about the currently installed SATA hard drives. Press the TAB key to move to the Free Disks section. Select the target hard drives using the UP or DOWN ARROW key and use the RIGHT ARROW key to add the hard drives to the Array Disks section FigureEnglish B Set BootN New Array ENTER Detail R Rebuildcd bootdrv menu 4 Making a SATA Driver DiskEnglish Note For users without a startup diskPress F6 if you need to install a 3rd party SCSI or RAID driver 5 Installing SATA controller driver during OS installationEnglish S=Specify Additional Device ENTER=Continue F3=ExitENTER=Select F3=Exit EnglishS=Specify Additional Device Enter=Continue F3=Exit English 1 Installing SATA hard drives in your computer B. GIGABYTE SATA2 Controller2 Configuring SATA controller mode and boot sequence in BIOS Setup EnglishEnglish Step Save and exit BIOS SetupStep GA-N680SLI-DQ6 MotherboardEnglish 3 Configuring RAID array in RAID BIOSEnglish A. Create ArraySteps English 3. Assign Array Disks After RAID mode is selected, RAID BIOS automatically assigns the two hard disks installed as the RAID disksCreate RAID Disk Drive EnglishSave And Exit Setup EnglishEnglish B. Delete ArrayDelete RAID Disk Drive cd bootdrv menu 4 Making a SATA Driver Disk Required for AHCI and RAID ModeA command prompt window will open similar to that in Figure EnglishEnglish English Step EnglishGA-N680SLI-DQ6 Motherboard 4-1-5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsEnglish English 4 Channel Audio SetupEnglish 6 Channel Audio SetupEnglish 8 Channel Audio SetupAC97 Audio Configuration Sound Effect ConfigurationEnglish English Enabling the DTS Digital Theater Systems functionDTS control button Introduction of Dolby Digital Live Digital PCM Output SetupEnglish English 4-1-6 Windows Vista ReadyBoostProperties English 4-2 TroubleshootingGA-N680SLI-DQ6 Motherboard EnglishAppendix EnglishGA-N680SLI-DQ6 Motherboard EnglishAppendix EnglishEnglish Contact UsEnglish y GIGABYTE Global Service SystemThen select your language to enter the system