Manuals / Intel / Computer Equipment / Computer Monitor

Intel TPC-1070 Appendix G Fuse Specifications, G.1 Fuse Specifications, G.2 Fuse Replacement

Models: TPC-1070

1 92

Download 92 pages 45.44 Kb

Page 92

Appendix G Fuse Specifications

Appendix G Fuse Specifications

G.1 Fuse Specifications

Rating: 250VAC, 3.15Amp

Size: 5 x 20mm

Note

The fuse is set to break as the input voltage exceeds 33VDC for your protection.

G.2 Fuse Replacement

Step 1: Remove the fuse cover

Step 2: Replace the damaged fuse with a new one

Step 3: Place the fuse cover back in position

Figure G.1: Fuse Replacement

Warning

Do NOT replace the fuse unless it is damaged. Do NOT replace the fuse with a different rating.

TPC-1070 User Manual

80

Image 92

Intel TPC-1070 Appendix G Fuse Specifications, G.1 Fuse Specifications, G.2 Fuse Replacement, Figure G.1 Fuse Replacement

Contents

Intel Touch Panel Computer with High Luminance SVGA TFT LCD User ManualTPC-1070 Copyright Acknowledgements1st Edition Printed in TaiwanProduct Warranty 2 years Technical Support and Assistance Declaration of Conformity CEFCC Class A Safety Instructions Wichtige Sicherheishinweise 11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspan- nung eine Beschädigung vermieden TPC-1070 User Manual viiiContents COM1/ COM3 Connector Definition Table of Contents Fuse SpecificationsFuse Specifications Fuse ReplacementTPC-1070 User Manual General Information CHAPTER1.2 Specifications Chapter 1 General Information1.1 Introduction Powerful Communication Capability1.2.3 Safety and Environment Safety1.2.2 I/O Ports 2 RJ-45 Ethernet port1.3 LCD Specifications TPC-1070 User Manual1.4 Touchscreen Specifications 1.5 PowerTypical 24V@2.5A 60W Chapter1TPC-1070 User Manual 1.6 I/O Port ArrangementFigure 1.1 I/O port arrangement 1.7 Panel Mounting Figure 1.2 Panel MountingTPC-1070 User Manual 1.8 Dimensions & CutoutFigure 1.3 Dimensions System Setup CHAPTERFigure 2.2 Power connector Chapter 2 System SetupFigure 2.1 Install CompactFlash memory card Figure 2.3 Power receptor and button pin assignments Figure 2.4 Touchscreen Calibration Figure 2.5 Touchscreen Calibration TPC-1070 User ManualSystem Engine CHAPTERChapter 3 System Engine Main Board Connector and Jumper Setting ListFigure 3.1 Main Board Connector TPC-1070 User ManualSoftware Configuration Advantech COM Driver Installation Watchdog Timer Driver InstallationCHAPTER Sections include Utilities & Drivers4.1 Utilities & Drivers Chapter 4 Software Configuration4.1.1 Intel Chipset Software Installation Utility 4.1.2 VGA Drivers IntelR Graphics Driver4.1.6 Watchdog Timer Driver 4.1.4 Advantech COM Driver4.1.5 Touchscreen Driver Path \TPC-1070H\Driver\Advantech COM\ Available for the OS’s below4.2 Advantech COM Driver Installation Step 1 Insert the companion CD-ROM into your CD-ROM drive. Openthe directory \TPC-1070H\Driver\Advantech COM\ TPC-1070 User ManualChapter4 Step 3 Click Next to continue installationStep 4 Click Next to continue installation Step 5 Click uninstall icon to remove ?PCI Serial Port TPC-1070 User ManualChapter4 Step 7 Found New Hardware and Click Next to continue installation TPC-1070 User ManualChapter4 Step 8 Click Finish the Advantech PCI Serial Port to continueStep 9 Then, found New Hardware and Click Next to continue TPC-1070 User Manual Chapter4 Step 11 Found New Hardware and Click Next to continue installationStep 12 Click Finish the Advantech PCI Serial Port to continue 4.3 Watchdog Timer WDT Driver Installation 4.3.1 Installing the TPC-1070 Watchdog Timer Driver Step 1 Insert the companion CD-ROM into your CD-ROM drive. Openthe directory \WDT\8362x\W2KXP Chapter4Step 3 Click Next to proceed TPC-1070 User ManualChapter4 Step 5 Select Advantech W83627HF Watchdog Timer and click NextStep 4 Click Next to confirm the customer information TPC-1070 User Manual Step 6 Click Next to confirm selecting the Typical setup typeStep 7 Click Next to proceed Chapter4 Step 8 Click Finish to complete the procedureStep 9 Click OK to restart the system and activate the Watchdog Timer 4.3.2 How to Use the TPC-1070 Watchdog Timer Step 1 Open the Control Panel, click Watchdog Service ConfigurationStep 2 Click the Start Service button TPC-1070 User ManualChapter4 Step 3 Click Setting to select the setting pageStep 4 Select the Timer Span that meets your application requirement Step 5 Click Enable to enable the setting Step 7 Click OK, then the configuration procedure is finishedUse Advantech WDT Driver.WDT was enable,and WDT LED was 1Hz glisten TPC-1070 User ManualSections include EWF HORM Advantech Utilities Windows XP EmbeddedCHAPTER 5.2 HORM Chapter 5 Windows XP Embedded5.1 EWF 5.3 Advantech Utilities 5.3.1 Version Information5.3.2 OSLock and OSUnLock 5.3.3 HORMSerial Port Settings APPENDIX AA.2 COM4 Setting Appendix A Serial Port SettingsA.1 COM1/ COM3 Connector Definition RS232 RS485RS422-MASTER RS422-SLAVETPC-1070 User Manual Watchdog Timer on WinCE APPENDIXAppendix B Watchdog Timer on WinCE B.1 DeviceIOControllpInBuffer B.2 How to Use the Control Code IOCTL WDTENABLEIOCTL WDTDISABLE IOCTLWDTSTROBEIOCTLWDTREBOOT IOCTLWDTGETTIMEOUTIOCTLWDTSETTIMEOUT B.3 Examples Enable the Watchdog timer TPC-1070 User Manual Watchdog Timer Programming APPENDIXAppendix C Watchdog Timer Programming C.1 OverviewChapterC C.2 Watchdog Timer ProgrammingFigure C.1 Watchdog timer programming procedure Table C.1 Watchdog Timer Registers Address ofAttribute DescriptionC.3 Example Programs 1. Enable watchdog timer and set 10 sec. as timeout interval2. Enable watchdog timer and set 5 minutes as timeout interval 3. Enable watchdog timer to be reset by mouse 4. Enable watchdog timer to be reset by keyboard 5. Generate a time-out signal without timer counting Dec dx Enable the function of watchdog timer Mov al,30h Dec dx Generate a time-out signal Mov al,0f7hOut dx,al Inc dx Mov al,01h Out dx,al Out dx,al Write 1 to bit 5 of F7 register Inc dxAccessory Kit Assembly APPENDIX DAppendix D Accessory Kit Assembly D.1 CompactFlash to IDE Transfer KitFigure D.2 Connecting Adapter Board & IDE Cable Figure D.1 Adapter Board and IDE CablePin 1 is marked red Figure D.3 CompactFlash SlotFigure D.4 Insert the Adapter Board into the CF slot Figure D.5 Inserted Adapter BoardD.2 USB Driver Installation Notice Figure D.7 Plug Power Line into CD-ROM Drive4 is installed before you install the USB driver on Windows 2000. Service Pack 1 mustHDD Kit Assembly APPENDIX EAppendix E HDD Kit Assembly Figure E.3 Installing the HDDFigure E.1 Removing the Rear HDD Cover Figure E.2 Removing the Top ScrewsTouchscreen Installation Configuration APPENDIX FAppendix F Touchscreen Installation & Configuration F.1 Driver InstallationFigure F.1 Setup.exe Figure F.2 Install - WizardAppendixF Figure F.3 Install - License AgreementFigure F.4 Install - Completed F.2 Uninstall the Driver Figure F.5 UninstallFigure F.6 Uninstall TPC-1070 User ManualCalibrate F.3 Touchscreen CalibrationFigure F.7 Uninstall Figure F.8 Standard Calibration Figure F.9 Standard Calibration TPC-1070 User ManualFigure F.10 Standard Calibration Touch the red squares in sequence. The calibration is completed after the fifth touch red point is calibrated. Press “ESC” to skipFigure F.11 Advanced Calibration Figure F.12 Advanced Calibration TPC-1070 User ManualPlot Calibration Data enabled provides the blue when you finished the advanced calibrationFigure F.13 Plot Calibration Data lines to show linearity before calibration andFigure F.14 Draw Click “menu” and then click “clear screen” to clear the drawingFigure F.15 Clear Screen TPC-1070 User ManualOption Figure F.16 OptionTPC-1070 User Manual Fuse Specifications APPENDIXGAppendix G Fuse Specifications G.1 Fuse SpecificationsG.2 Fuse Replacement Figure G.1 Fuse Replacement