Manuals
/
Jackson
/
Kitchen Appliance
/
Dishwasher
Jackson
10AB, 10APRB, 10U operation manual Section Specification Information
Models:
10U
10AB
10A
10APRB
1
6
33
33
Download
33 pages
29.14 Kb
3
4
5
6
7
8
9
10
<
>
Specification
Install
Section Electrical Schematics
Warranty
Dimension
Maintenance
PLUMBING THE DISHMACHINE All plumbing connections must comply with all applicable local, state, and national plumb- ing codes. The plumber is responsible for ensuring that the incoming water line is thoroughly flushed prior to connecting it to any component of the dishmachine. It is necessary to remove all foreign debris from the water line that may potentially get trapped in the valves or cause an obstruction. Any valves that are fouled as a result of foreign matter left in the water line, and any expenses resulting from this fouling, are not the responsibility of the manufacturer
LEVEL THE DISHMACHINE The dishmachine is designed to operate while being level. This is important to prevent any damage to the machine during operation and to ensure the best results when washing ware. The unit comes with adjustable bullet feet, which can be turned using a pair of channel locks or by hand if the unit can be raised safely. Ensure that the top of the tub is level from side to side and from front to back before making any con- nections
10A 208/220V 1 PHASE
GCS SERVICE INC. 1002 NANDINO BLVD. LEXINGTON, KY
Page 6
Image 6
SECTION 1:
SPECIFICATION INFORMATION
1
Page 5
Page 7
Page 6
Image 6
Page 5
Page 7
Contents
FOR JACKSON MODELS 10A 10AB 10APRB 10U HIGHER HOOD OPTION
An Company
10 SERIES, ELECTRICALLY HEATED, ROUND DISHMACHINES
February 24 P/N 7610-100-01-00 Revision E
ONE YEAR LIMITED PARTS & LABOR WARRANTY
MANUFACTURERS WARRANTY
MADE
REVISION
REVISION
APPLICABLE
Model Serial No Installation Date Service Rep. Name Phone No
10 SERIES
NOMENCLATURE FOR THE MODELS COVERED IN THIS MANUAL
TABLE OF CONTENTS
SECTION SPECIFICATION INFORMATION
SECTION 1 SPECIFICATION INFORMATION 10 SERIES SPECIFICATIONS
LEFT VIEW
SECTION 1 SPECIFICATION INFORMATION 10A DIMENSIONS
TOP VIEW
FRONT VIEW
TOP VIEW
SECTION 1 SPECIFICATION INFORMATION
10AB/10APRB/10U DIMENSIONS
FRONT VIEW
SECTION 1 SPECIFICATION INFORMATION 10 SERIES TABLE DIMENSIONS
SECTION INSTALLATION/OPERATION INSTRUCTIONS
SECTION 2 INSTALLATION/OPERATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
LEVEL THE DISHMACHINE The dishmachine is designed to operate while being level. This is important to prevent any damage to the machine during operation and to ensure the best results when washing ware. The unit comes with adjustable bullet feet, which can be turned using a pair of channel locks or by hand if the unit can be raised safely. Ensure that the top of the tub is level from side to side and from front to back before making any con- nections
ALIGNING THE MACHINE Adjust the machine base to line up hole in table with hole in support block Fig
PLUMBING THE DISHMACHINE All plumbing connections must comply with all applicable local, state, and national plumb- ing codes. The plumber is responsible for ensuring that the incoming water line is thoroughly flushed prior to connecting it to any component of the dishmachine. It is necessary to remove all foreign debris from the water line that may potentially get trapped in the valves or cause an obstruction. Any valves that are fouled as a result of foreign matter left in the water line, and any expenses resulting from this fouling, are not the responsibility of the manufacturer
SECTION 2 INSTALLATION/OPERATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
SECTION 2 INSTALLATION/OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS
PREPARATION
SECTION 2 INSTALLATION/OPERATION INSTRUCTIONS DETERGENT CONTROL
SECTION PREVENTATIVE MAINTENANCE
SECTION 3 PREVENTATIVE MAINTENANCE PREVENTATIVE MAINTENANCE
SECTION ELECTRICAL SCHEMATICS
10AB/10U 208/220V 1 PHASE
L2 L1
10A 208/220V 1 PHASE
3 PHASE
SECTION 4 ELECTRICAL SCHEMATICS
10A WIRING DIAGRAM 208-230 VOLT, 60HZ, SINGLE PHASE
SECTION 4 ELECTRICAL SCHEMATICS
10AB WIRING DIAGRAM 208-230 VOLT, 60HZ, SINGLE PHASE
SECTION 4 ELECTRICAL SCHEMATICS
10AB WIRING DIAGRAM 208-230 VOLT, 60HZ, THREE PHASE
9905-002-55-90a
SECTION 4 ELECTRICAL SCHEMATICS
10APRB WIRING DIAGRAM 208-230 VOLT, 60HZ, SINGLE PHASE
9905-002-55-91a
SECTION 4 ELECTRICAL SCHEMATICS
10APRB WIRING DIAGRAM 208-230 VOLT, 60HZ, THREE PHASE
9905-002-55-92a
SECTION JACKSON MAINTENANCE REPAIR CENTERS
SECTION 5 JACKSON MAINTENANCE & REPAIR CENTERS
EMR SERVICE DIVISION 2626 PITTMAN DRIVE SILVER SPRING, MD
GCS SERVICE INC. 1002 NANDINO BLVD. LEXINGTON, KY
EMR SERVICE DIVISION 700 EAST 25TH STREET BALTIMORE, MD
BANA PARTS INC. 1501 KUEBLE STREET HARAHAN, LA
200 SALINA ST. SUITE 114 LIVERPOOL, NY
HAWKINS COMMERCIAL APPLI
1900 COLLEGE AVENUE ELMIRA HEIGHTS, NY
800 532-6127 FAX
ELMER SCHULTZ SVC. 540 NORTH 3RD STREET PHILADELPHIA, PA
CANADA
GCS/STOVE PARTS 2120 SOLANA STREET FORT WORTH, TX
NORTHERN PARTS & SVC. 4874 S. CATHERINE STREET PLATTSBURGH, NY