SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

OPERATION INSTRUCTIONS

PREPARATION: Before proceeding with the start-up of the unit, verify the following:

1.The sump strainer is in place and is clean.

2.The drain stopper is installed.

3.That the wash and rinse arms are screwed securely into place and that their endcaps are tight. The wash and rinse arms should rotate freely.

POWER UP: To energize the unit, turn on the power at the service breaker. The voltage should have been previously verified as being correct. If not, the voltage will have to be verified.

FILLING THE WASH TUB: For the initial fill, close doors and depress and hold the OFF/ON/FILL rocker switch in the FILL position for approximately 8 - 10 seconds. Open the doors and verify that the water level is correct. Hereafter, the water level is controlled by the timer that has been preset at the factory. Verify that the drain stopper is preventing the wash tub water from pouring out excessively. There may be some slight leakage from the drain hole. Verify that there are no other leaks on the unit before proceeding any further. The wash tub must be completely filled before operating the wash pump to prevent damage to the component. Once the wash tub is filled, the unit is ready for operation.

The water level was set at the factory. If the water level is not at the level noted above, it will require adjustment. Check to ensure that the recommended water pressure is being supplied to the machine (20±5 PSI). If the water pressure is correct then the fill valve will need adjustment. Use the following steps to adjust the cam. Turn power off at the machine circuit break- er. Open the control box cover. Locate the timer fill valve cam (Cam 4 from the timer motor). Locate the spanner wrench taped to the electrical panel. The spanner wrench is used to adjust the cam.

To increase the water level, open the notch of the adjustable cam. To decrease the water level, close the notch. Care must be taken that the set point does not extend into the home position of the timer. Do not move the side of the cam that starts the fill; this will change the sequence of cycle operation. With the door closed turn the power circuit breaker on. Open and close the door to run a cycle, then check the water level. Adjust as necessary then close the control box cover.

The machine runs a complete cycle to drain and fill. If the machine is not allowed to drain, the water will build up inside the tub. After the initial fill, the rinse water for the current cycle will become the wash water for the next cycle.

WARE PREPARATION: Proper preparation of ware will help ensure good results and less re-washes. If not done properly, ware may not come out clean and the efficiency of the dishmachine will be reduced. It is important to remember that a dishmachine is not a garbage disposal and that simply throwing unscraped dishes into the machine simply defeats the purpose altogether of washing the ware. Scraps should be removed from ware prior to being loaded into a rack. Pre-rinsing and pre-soaking are good ideas, especially for silverware and casserole dishes.

Place cups and glasses upside down in racks so that they do not hold water during the cycle. The dishmachine is meant not only to clean, but to sanitize as well, to destroy all of the bacteria that could be harmful to human beings. In order to do this, ware must be properly prepared prior to being placed in the machine.

DAILY MACHINE PREPARATION: Refer to the section entitled “PREPARATION” at the top of this page and follow the instruc- tions there. Afterwards, check that all of the chemical levels are correct and/or that there is plenty of detergent available for the expected workload.

WARM-UP CYCLES: For a typical daily start-up, it is recommended to run the machine through 3 cycles to ensure that all of the cold water is out of the system and to verify that the unit is operating correctly. To cycle the machine, ensure that the power is on and that the tub has filled to the correct level. Lift the doors and the cycle light will illuminate. When the light goes out, close the doors, the unit will start, run through the cycle, and shut off automatically. Repeat this two more times. The unit should now be ready to proceed with the washing of ware.

Conserver XL Series Technical Manual 7610-002-10-23

Issued: 11-28-2007 Revised: N/A

18

Page 24 Page 26
Page 25
Image 25
Jackson AXL2-CML, AXL2-CMR technical manual Operation Instructions
Page 24 Page 26

XL2-CML, XL2-CMR, AXL2-CMR, AXL2-CML, AXL2 specifications

The Jackson XL2, AXL, AXL2, AXL2-CML, and AXL2-CMR represent a remarkable lineage of advanced electric guitars designed for superior playability, tonal versatility, and innovative technology. These instruments cater to musicians of all levels, from aspiring guitarists to seasoned professionals, offering a blend of classic styling and modern features.

The Jackson XL2 model is characterized by its sleek body design and a set-neck construction that enhances sustain and allows for effortless access to higher frets. The guitar comes equipped with high-output pickups that deliver powerful tones, making it ideal for rock and metal genres. Its distinctive headstock design not only adds to its aesthetic appeal but also aids in tuning stability.

Moving to the AXL series, these guitars incorporate a double-cutaway body shape that provides excellent comfort while playing. The AXL models are known for their versatility, sporting a range of pickup configurations that allow for a wide spectrum of sounds. Players can expect a balance between aggressive tones and smooth, melodic qualities, making it suitable for various playing styles.

The AXL2 builds upon its predecessor’s capabilities, featuring an improved ergonomic design that enhances comfort during long playing sessions. The inclusion of enhanced electronics provides greater tonal options, and the instrument's lightweight construction ensures ease of handling. The AXL2-CML variant introduces a sleek matte finish, appealing to modern aesthetics while retaining robust playability.

For those seeking even more specialized features, the AXL2-CMR variant is designed with custom routing options and unique pickup placements that cater to the needs of advanced players. This version offers superior tonal clarity and response, making it perfect for intricate playing styles and complex musical compositions.

All these models showcase an attention to detail in craftsmanship, employing premium materials that ensure durability and longevity. With innovations such as locking tuners, push-pull coil-splitting features, and more, the Jackson XL2, AXL, AXL2, AXL2-CML, and AXL2-CMR cater to musicians looking for reliability and performance on stage or in the studio. Whether you are looking for raw power, tonal versatility, or refined aesthetics, these guitars meet a broad range of musical needs, making them indispensable for any guitarist.
Top Page Image Contents