CONTROLS AND SETUP

SPECIFICATIONS

SETTING THE

SETTING INPUT

CROSSOVER(S)

SENSITIVITY

CS200.1

• 1 x 236W RMS channel at 4 ohms and 1% THD + N

Declaration of Conformity

Determine your system plans and set the crossover mode switch accordingly. If you plan to use the CS50.4 to drive full- range speakers, set the crossover mode to FLAT and skip to “Setting Input Sensi- tivity.”

Initially set the crossover frequency control midway. While listening to music, adjust the crossover for the least per- ceived distortion from the speakers, allowing them to reproduce as much bass as possible.

Systems using a separate subwoofer set the crossover mode to HP (high pass) for your full-range speakers. Adjust the crossover frequency to limit bass and provide increased system volume with less distortion.

For subwoofers, choose the highest frequency that removes vocal information from the sound of the subwoofer.

If using the CS50.4 to drive a subwoofer(s), set the crossover mode to LP (low pass).

1.Initially turn the INPUT LEVEL control(s) to minimum (counter clockwise).

2.Reconnect the (–) negative lead to the vehicle’s battery. Apply power to the audio system and play a dynamic music track.

3.On the source unit, increase the vol- ume control to 3/4 volume. Slowly increase the INPUT LEVEL control(s) toward three o’clock until you hear slight distortion

in the music. Then reduce the INPUT LEVEL slightly until distortion is no longer heard.

NOTE: After the source unit is on, blue LEDs (on the top panel) will light, indicat- ing the amplifier is on. If not, check the wiring, especially the remote connection from the source unit. Also refer to “Troubleshooting” guide below.

Signal-to-noise ratio: 100dBA (reference 1W into 4 ohms)

• 1 x 338W RMS channel at 2 ohms, 14.4V supply and

1% THD + N

• Dynamic power: 464W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 302Hz (–3dB)

• Maximum input signal: 7.5V

• Maximum sensitivity: 260mV

• Output regulation: .073dB at 4 ohms

• Dimensions (L x W x H): 295x313x60mm

(11-5/8" x 12-5/16" x 2-3/8")

• Fuses: 20A x 2

CS50.4

• 4 x 67W RMS channels at 4 ohms and 1% THD + N

Signal-to-noise ratio: 86dBA (reference 1W into 4 ohms)

• 4 x 82W RMS channels at 2 ohms, 14.4V supply and

1% THD + N

• 2 x 162W RMS channels at 4 ohms, 14.4V supply and

1% THD + N

• Dynamic power: 145W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 27kHz (–3dB)

• Maximum input signal: 6V

• Maximum sensitivity: 240mV

• Output regulation: .032dB at 4 ohms

• Dimensions (L x W x H): 384x313x60mm

(15-1/8" x 12-5/16" x 2-3/8")

We, Harman Consumer International

2, route de Tours

72500 Chateau-du-Loir

France

declare in own responsibility that the product described in this owner’s manual is in compliance with technical standards:

EN 55013:2001

EN 55020:2002

Emmanuel Millot

Harman Consumer International

Chateau-du-Loir, France 1/04

JBL Consumer Products

250 Crossways Park Drive,

Woodbury, NY 11797 USA

©2004 Harman International Indus- tries, Incorporated

JBL and Grand Touring are registered trademarks of Harman International Industries, Incorporated.

Part No. CSAMPOM3/04

TROUBLESHOOTING

SYMPTOM

LIKELY CAUSE

SOLUTION

No audio

No voltage at BATT+

Check voltages at

(POWER LED

or REM terminals,

amplifier terminals

are off)

or bad or no ground

with VOM

 

connection

 

No audio

Amplifier is

Make sure amplifier

(POWER

overheated

cooling is not blocked

LEDs are on)

 

at mounting location;

 

 

verify speaker system

 

 

impedance is within

 

 

specified limits

 

Voltage more than 16V

Check vehicle

 

or less than 8.5V on

charging system

 

BATT+ connection

 

www.jbl.com

Features, specifications and appearance

are subject to change without notice.

 

• Fuses: 25A x 2

SYMPTOM

LIKELY CAUSE

SOLUTION

No audio

Voltage less than 9V on

Check vehicle

(POWER

BATT+ connection

charging system

LEDs flash)

DC voltage on

Amplifier may need

 

 

amplifier output

service; see enclosed

 

 

warranty card for

 

 

service information

Distorted audio

Input sensitivity is

Check INPUT

 

not set properly, or

LEVEL setting; or

 

amplifier or source

check speaker wires

 

unit is defective

for shorts or grounds

Distorted audio

Short circuit in

Remove speaker leads

and POWER

speaker or wire

one at a time to locate

LED flash

 

shorted speaker or

 

 

wire, then repair

Music lacks

Speakers are not

Check speaker

“punch”

connected properly

connections for proper polarity

Page 4
Image 4
JBL CS50.4, CS200.1 Controls and Setup Specifications, Troubleshooting, Setting Setting Input Crossovers Sensitivity