Dolby Pro Logic
Use this installation method for | output, or a | level inputs on the subwoofer. | ||||||
Dolby Pro Logic | preamp | IMPORTANT: Do not use the | ||||||
(not Dolby Digital, DTS® or |
| Use | LFE input on the subwoofer | |||||
other digital processing), where | to connect the | with Dolby Pro Logic | ||||||
the receiver/processor is |
| subwoofer outputs on your | processors. Note: If your | |||||
equipped with a subwoofer | receiver or amplifier to the line- | receiver or amplifier only has | ||||||
|
|
|
|
|
|
|
| one subwoofer output jack, |
Left Front |
| Center |
| Right Front | then you will need to use a Y- | |||
+ | – |
| + | – |
| + | – | connector (not included). Plug |
|
|
|
| the male end of the Y- | ||||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| connector into your receiver or |
|
|
| Subwoofer |
|
|
| amplifier’s subwoofer output | |
|
|
|
|
|
| jack, and connect each of the | ||
|
|
| Line- |
|
|
| ||
|
|
| Level In |
|
|
| two female ends to separate | |
|
|
| L |
|
|
|
| |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |
|
|
| R |
|
|
|
| plug the |
|
|
| Receiver |
|
|
| into the | |
|
|
|
|
|
| subwoofer. | ||
|
| Left | Subwoofer | Right |
|
| ||
|
|
|
| Connect each speaker to the | ||||
| Front | Out |
| Front |
|
| ||
| + | – | R | L | + | – |
| corresponding speaker |
|
|
|
|
|
| terminals on your receiver or | ||
|
|
| + | – |
|
|
| |
|
|
|
|
|
| amplifier. | ||
|
|
|
|
|
|
|
| |
|
| Left | Center | Right |
|
| ||
|
| Surround Back |
|
| ||||
| Surround | Surround |
|
| ||||
| + | – | + | – | + | – |
|
|
Left Surround |
| Surround Back |
| Right Surround |
| |||
+ | – |
| + | – |
| + | – |
|
|
| Only in 6.1 systems |
|
|
|
Dolby Digital or DTS® (or Other Digital Surround Mode) Connection (SCS 178 and SCS 188)
|
| RECEIVER | SUBWOOFER | output or subwoofer output | front right, center and rear | ||||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
| LINE LEVEL IN | on your receiver or amplifier. | speakers should all be set to | ||||
|
|
|
|
|
|
| L |
| Connect each speaker to the | “Small.” | |
|
| LFE OUT |
| LFE INPUT | |||||||
|
|
| corresponding speaker | If your receiver allows you to | |||||||
|
|
|
|
|
|
| R |
| |||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| terminals on your receiver or | set the crossover frequency | |
|
|
|
|
|
|
|
|
| amplifier. | between the subwoofer and the |
|
|
|
|
|
|
|
|
|
|
| ||
|
| Use this installation method for | Make sure that you have | main speakers, select either |
| ||||||
|
| Dolby Digital, DTS® or other | configured your surround- | 120Hz or 150Hz, or select the |
| ||||||
|
| digital surround processors: | sound processor for | setting that is the closest |
| ||||||
|
| Use the | “Subwoofer On.” The surround | frequency below these. |
| ||||||
|
| marked “LFE” for the Low- | receiver should be configured |
|
| ||||||
|
| Frequency Effects channel. | for |
|
| ||||||
|
| 6Connect this jack to the LFE | (if available) and the front left, |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|